Bed composition generation for morphodynamic modeling: case study of San Pablo Bay in California, USA
TL;DR: In this paper, a bed composition generation (BCG) run does not include bed level changes, but does permit the redistribution of multiple sediment fractions over the modeled domain, and is applied to San Pablo Bay in California, USA.
read more
Abstract: Applications of process-based morphodynamic models are often constrained by limited availability of data on bed composition, which may have a considerable impact on the modeled morphodynamic development. One may even distinguish a period of “morphodynamic spin-up” in which the model generates the bed level according to some ill-defined initial bed composition rather than describing the realistic behavior of the system. The present paper proposes a methodology to generate bed composition of multiple sand and/or mud fractions that can act as the initial condition for the process-based numerical model Delft3D. The bed composition generation (BCG) run does not include bed level changes, but does permit the redistribution of multiple sediment fractions over the modeled domain. The model applies the concept of an active layer that may differ in sediment composition above an underlayer with fixed composition. In the case of a BCG run, the bed level is kept constant, whereas the bed composition can change. The approach is applied to San Pablo Bay in California, USA. Model results show that the BCG run reallocates sand and mud fractions over the model domain. Initially, a major sediment reallocation takes place, but development rates decrease in the longer term. Runs that take the outcome of a BCG run as a starting point lead to more gradual morphodynamic development. Sensitivity analysis shows the impact of variations in the morphological factor, the active layer thickness, and wind waves. An important but difficult to characterize criterion for a successful application of a BCG run is that it should not lead to a bed composition that fixes the bed so that it dominates the “natural” morphodynamic development of the system. Future research will focus on a decadal morphodynamic hindcast and comparison with measured bathymetries in San Pablo Bay so that the proposed methodology can be tested and optimized.
read more
Chat with Paper
AI Agents for this Paper
Find similar papers on Google Scholar, PubMed and Arxiv
Write a critical review of this paper
Analyze citations of this paper to find unaddressed research gaps
Citations
Tidal inlet sediment bypassing at mixed-energy barrier islands
Gerald Herrling,Christian Winter +1 more
TL;DR: In this paper, a model of sediment bypassing at non-migrating, mixed-energy tidal inlets is discussed based on process-based numerical modeling of sediment dynamics at an exemplary barrier island system in the southern North Sea.
31
Modeling the Hydrodynamic and Morphologic Response of an Estuary Restoration
TL;DR: In this article, an innovative river sediment discharge schematization was developed that connected sediment discharge to morphological change in the estuary, and a conceptual model covering morphology and indicators of physical habitat for three phases of estuary evolution during restoration was presented that could be applied to estuarine systems that are severely out of equilibrium.
27
First-order uncertainty analysis using Algorithmic Differentiation of morphodynamic models
TL;DR: An efficient first-order second moment method using Algorithmic Differentiation (FOSM) and a Tangent Linear Model (TLM) which can be applied to quantify uncertainty/sensitivities in morphodynamic models is presented.
25
Modelling-based assessment of suspended sediment dynamics in a hypertidal estuarine channel
TL;DR: In this paper, the authors investigate the dynamics of suspended sediment transport in a hypertidal estuarine channel which displays a vertically sheared exchange flow and apply a three-dimensional process-based model coupling hydrodynamics, turbulence and sediment transport to the Dee Estuary.
References
A third-generation wave model for coastal regions: 1. Model description and validation
TL;DR: In this article, a third-generation numerical wave model to compute random, short-crested waves in coastal regions with shallow water and ambient currents (Simulating Waves Nearshore (SWAN)) has been developed, implemented, and validated.
•Book
Principles of sediment transport in rivers, estuaries and coastal seas
Leo C. van Rijn
- 01 Jan 1993
2.3K
Development and validation of a three-dimensional morphological model
TL;DR: The DELFT3D-FLOW module as discussed by the authors is a 3D flow solver for modeling sediment transport patterns in the water column of the DELFT-3D flow model, which is used to model both suspended and bedload transport of noncohesive sediment.
1.9K
A third‐generation wave model for coastal regions: 2. Verification
TL;DR: In this article, a third-generation spectral wave model for small-scale, coastal regions with shallow water, (barrier) islands, tidal flats, local wind, and ambient currents is verified in stationary mode with measurements in five real field cases.
1.2K
•Book
Introduction to the Physics of Cohesive Sediment in the Marine Environment
Johan C. Winterwerp,Walther G.M. van Kesteren +1 more
- 04 Apr 2013
TL;DR: In this article, boundary layer flow and sediment-fluid interaction in cohesive sediment are investigated. But the 1DV Point Model is not suitable for the measurement of cohesive sediment.
652