Bed composition generation for morphodynamic modeling: case study of San Pablo Bay in California, USA
TL;DR: In this paper, a bed composition generation (BCG) run does not include bed level changes, but does permit the redistribution of multiple sediment fractions over the modeled domain, and is applied to San Pablo Bay in California, USA.
read more
Abstract: Applications of process-based morphodynamic models are often constrained by limited availability of data on bed composition, which may have a considerable impact on the modeled morphodynamic development. One may even distinguish a period of “morphodynamic spin-up” in which the model generates the bed level according to some ill-defined initial bed composition rather than describing the realistic behavior of the system. The present paper proposes a methodology to generate bed composition of multiple sand and/or mud fractions that can act as the initial condition for the process-based numerical model Delft3D. The bed composition generation (BCG) run does not include bed level changes, but does permit the redistribution of multiple sediment fractions over the modeled domain. The model applies the concept of an active layer that may differ in sediment composition above an underlayer with fixed composition. In the case of a BCG run, the bed level is kept constant, whereas the bed composition can change. The approach is applied to San Pablo Bay in California, USA. Model results show that the BCG run reallocates sand and mud fractions over the model domain. Initially, a major sediment reallocation takes place, but development rates decrease in the longer term. Runs that take the outcome of a BCG run as a starting point lead to more gradual morphodynamic development. Sensitivity analysis shows the impact of variations in the morphological factor, the active layer thickness, and wind waves. An important but difficult to characterize criterion for a successful application of a BCG run is that it should not lead to a bed composition that fixes the bed so that it dominates the “natural” morphodynamic development of the system. Future research will focus on a decadal morphodynamic hindcast and comparison with measured bathymetries in San Pablo Bay so that the proposed methodology can be tested and optimized.
read more
Chat with Paper
AI Agents for this Paper
Find similar papers on Google Scholar, PubMed and Arxiv
Write a critical review of this paper
Analyze citations of this paper to find unaddressed research gaps
Citations
Morphodynamics of tidal networks: advances and challenges
TL;DR: The approach to long-term predictions is discussed, the coupling between physical and biological processes are focused on, and the role of anthropic drivers in the evolution of these systems are introduced.
177
Reproduction of estuarine bathymetry by means of a process-based model: Western Scheldt case study, the Netherlands
TL;DR: In this article, a 3D morphodynamic, process-based numerical model (Delft3D) is proposed to investigate the processes governing the evolution of major morphological features in alluvial estuaries as well as their morphodynamic interaction with the geometry by means of a three-dimensional model.
119
Assessment of a numerical model to reproduce event‐scale erosion and deposition distributions in a braided river
TL;DR: In this paper, a depth-averaged non-uniform sediment model (Delft3D) was used to predict the morphodynamics of a 2.5 km long reach of the braided Rees River, New Zealand, during a single high-flow event.
99
Process-based morphodynamic modeling of the Yangtze Estuary at a decadal timescale: Controls on estuarine evolution and future trends
TL;DR: In this paper, a process-based model system (Delft3D) is used to hindcast and forecast the morphodynamic evolution of the Yangtze Estuary at a decadal timescale.
92
Critical dependence of morphodynamic models of fluvial and tidal systems on empirical downslope sediment transport
TL;DR: It is found that it is impossible to calibrate a model on both sediment transport magnitude and morphology, which means that present calibration practice may cause an order magnitude error in either morphology or morphological change.
References
A third-generation wave model for coastal regions: 1. Model description and validation
TL;DR: In this article, a third-generation numerical wave model to compute random, short-crested waves in coastal regions with shallow water and ambient currents (Simulating Waves Nearshore (SWAN)) has been developed, implemented, and validated.
•Book
Principles of sediment transport in rivers, estuaries and coastal seas
Leo C. van Rijn
- 01 Jan 1993
2.3K
Development and validation of a three-dimensional morphological model
TL;DR: The DELFT3D-FLOW module as discussed by the authors is a 3D flow solver for modeling sediment transport patterns in the water column of the DELFT-3D flow model, which is used to model both suspended and bedload transport of noncohesive sediment.
1.9K
A third‐generation wave model for coastal regions: 2. Verification
TL;DR: In this article, a third-generation spectral wave model for small-scale, coastal regions with shallow water, (barrier) islands, tidal flats, local wind, and ambient currents is verified in stationary mode with measurements in five real field cases.
1.2K
•Book
Introduction to the Physics of Cohesive Sediment in the Marine Environment
Johan C. Winterwerp,Walther G.M. van Kesteren +1 more
- 04 Apr 2013
TL;DR: In this article, boundary layer flow and sediment-fluid interaction in cohesive sediment are investigated. But the 1DV Point Model is not suitable for the measurement of cohesive sediment.
652