Homogenization (climate)

Abstract: The microstructure evolution and mechanical properties of Ti2AlNb/Ti-36.5Zr–10Ni–15Cu-0.5Co-0.5Nb/Ti60 brazed joints before and after homogenization treatment were comprehensively evaluated. Initially, the joints brazed at 900 °C for 15 min exhibited a continuous coarse strip network of Ti2Cu, Ti2Ni, Zr2Cu and Zr2Ni brittle intermetallic compounds in the central region of the braze seam, which detrimentally affecting the mechanical properties. Subsequent homogenization at 600 °C for 1 h, the amount of continuous brittle intermetallic compounds significantly decreased through sufficient atomic diffusion. Concurrently, the inadequately transformed eutectic β-Ti within the intermetallic compounds underwent an active eutectoid reaction. This structural transformation established a coherent interface with elastic distortion between the α-Ti and intermetallic compounds, effectively minimizing the lattice mismatch. Thus, a widmanstatten structure (i.e., acicular intermetallic compounds within a eutectoid microstructure matrix) with improved mechanical properties was formed. Consequently, a mean shear strength of 350.3 MPa was attained after treatment at 600 °C for 1 h, marking a substantial 206 % increase compared to that before homogenization treatment. This finding underlines the pivotal role of homogenization treatment in optimizing the performance of aeroengine components.

Abstract: Abstract This study first developed a comprehensive semiautomatic data homogenization procedure to produce gap-infilled and homogenized monthly precipitation data series for 425 long-term/critical stations in Canada, which were then used to assess Canadian historical precipitation trends. Data gaps in the 425 series were infilled by advanced spatial interpolation of a much larger dataset. The homogenization procedure repeatedly used multiple homogeneity tests without and with reference series to identify changepoints/inhomogeneities, the results from which were finalized by manual analysis using metadata and visual inspection of the multiphase regression fits. As a result, 298 out of the 425 data series were found to be inhomogeneous. These series were homogenized using quantile matching adjustments. The homogenized dataset shows better spatial consistency of trends than does the raw dataset. The improved gridding and regional mean trend estimation methods also provide more realistic trend estimates. With these improvements, Canadian historical precipitation trends were found to be dominantly positive and significant, except in central-south Canada where the trends are generally insignificant and small with mixed directions. For annual precipitation, the largest increases are seen in southeastern Canada and along the Pacific coast; however, the largest relative increases (in percent of the 1961–90 mean) are seen in northern Canada. The largest trend difference between northern and southern Canada is seen in winter, in which significant increases in the north were matched with significant decreases in the south. Significance Statement This study aims to produce a homogenized long-term monthly precipitation dataset for Canada, which is then used to assess Canadian historical precipitation trends. The work is important because it developed a comprehensive algorithm for homogenization of precipitation data, and the results provide better representation of precipitation climate and more robust estimates of precipitation trends. It also identified the causes for large biases in the published estimates of precipitation trends over Canada.

Abstract: The effects of double-step homogenization processes on the precipitation of Al3Zr dispersoids and the dissolution of the primary phases of 2196 aluminum alloy were studied by optical microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). It was revealed that first-step homogenization facilitates the nucleation of Al3Zr, while second-step homogenization results in the dissolution of the primary phases and the growth of Al3Zr dispersoids. The nanosized θ’ precipitates formed in the first-step homogenization are dissolved after the second-step homogenization. The optimum homogenization process was selected as 400 °C/10 h + 520 °C/24 h, which effectively dissolves the primary phases and promotes the formation of refined distribution of Al3Zr dispersoids. This phenomenon is mainly caused by the highest nucleation rate of the Al3Zr phase at 400 °C. While reducing the heating rate of the homogenization process can increase the number density of the Al3Zr dispersoids and reduce the precipitate free zone (PFZ), it does not alleviate the inhomogeneity of the Al3Zr precipitation. These results are expected to be meaningful for tailoring the industrial homogenization processing of as-cast Al-Cu-Li alloy.