Abstract: China faces great challenges in protecting its soil from contamination caused by rapid industrialization and urbanization over the last three decades. Recent nationwide surveys show that 16% of the soil samples, 19% for the agricultural soils, are contaminated based on China’s soil environmental quality limits, mainly with heavy metals and metalloids. Comparisons with other regions of the world show that the current status of soil contamination, based on the total contaminant concentrations, is not worse in China. However, the concentrations of some heavy metals in Chinese soils appear to be increasing at much greater rates. Exceedance of the contaminant limits in food crops is widespread in some areas, especially southern China, due to elevated inputs of contaminants, acidic nature of the soil and crop species or cultivars prone to heavy metal accumulation. Minimizing the transfer of contaminants from soil to the food chain is a top priority. A number of options are proposed, including identification of the sources of contaminants to agricultural systems, minimization of contaminant inputs, reduction of heavy metal phytoavailability in soil with liming or other immobilizing materials, selection and breeding of low accumulating crop cultivars, adoption of appropriate water and fertilizer management, bioremediation, and change of land use to grow nonfood crops. Implementation of these strategies requires not only technological advances, but also social-economic evaluation and effective enforcement of environmental protection law.

Abstract: Microscopic plastic debris, termed “microplastics”, are of increasing environmental concern. Recent studies have demonstrated that a range of zooplankton, including copepods, can ingest microplastics. Copepods are a globally abundant class of zooplankton that form a key trophic link between primary producers and higher trophic marine organisms. Here we demonstrate that ingestion of microplastics can significantly alter the feeding capacity of the pelagic copepod Calanus helgolandicus. Exposed to 20 μm polystyrene beads (75 microplastics mL(–1)) and cultured algae ([250 μg C L(–1)) for 24 h, C. helgolandicus ingested 11% fewer algal cells (P = 0.33) and 40% less carbon biomass (P < 0.01). There was a net downward shift in the mean size of algal prey consumed (P < 0.001), with a 3.6 fold increase in ingestion rate for the smallest size class of algal prey (11.6–12.6 μm), suggestive of postcapture or postingestion rejection. Prolonged exposure to polystyrene microplastics significantly decreased reproductive output, but there were no significant differences in egg production rates, respiration or survival. We constructed a conceptual energetic (carbon) budget showing that microplastic-exposed copepods suffer energetic depletion over time. We conclude that microplastics impede feeding in copepods, which over time could lead to sustained reductions in ingested carbon biomass.

Abstract: The reactions between peroxymonosulfate (PMS) and quinones were investigated for the first time in this work, where benzoquinone (BQ) was selected as a model quinone. It was demonstrated that BQ could efficiently activate PMS for the degradation of sulfamethoxazole (SMX; a frequently detected antibiotic in the environments), and the degradation rate increased with solution pH from 7 to 10. Interestingly, quenching studies suggested that neither hydroxyl radical (•OH) nor sulfate radical (SO4•–) was produced therein. Instead, the generation of singlet oxygen (1O2) was proved by using two chemical probes (i.e., 2,2,6,6-tetramethyl-4-piperidinol and 9,10-diphenylanthracene) with the appearance of 1O2 indicative products detected by electron paramagnetic resonance spectrometry and liquid chromatography mass spectrometry, respectively. A catalytic mechanism was proposed involving the formation of a dioxirane intermediate between PMS and BQ and the subsequent decomposition of this intermediate into 1O2. Accordi...

Abstract: Plastic debris is one of the most significant organic pollutants in the aquatic environment. Because of properties such as buoyancy and extreme durability, synthetic polymers are present in rivers, lakes, and oceans and accumulate in sediments all over the world. However, freshwater sediments have attracted less attention than the investigation of sediments in marine ecosystems. For this reason, river shore sediments of the rivers Rhine and Main in the Rhine-Main area in Germany were analyzed. The sample locations comprised shore sediment of a large European river (Rhine) and a river characterized by industrial influence (Main) in areas with varying population sizes as well as sites in proximity to nature reserves. All sediments analyzed contained microplastic particles (<5 mm) with mass fractions of up to 1 g kg–1 or 4000 particles kg–1. Analysis of the plastics by infrared spectroscopy showed a large abundance of polyethylene, polypropylene, and polystyrene, which covered more than 75% of all polymer ty...

Abstract: High concentrations of plastic debris have been observed in the oceans. Much of the recent concern has focused on microplastics in the marine environment. Recent studies of the size distribution of the plastic debris suggested that continued fragmenting of microplastics into nanosized particles may occur. In this review we assess the current literature on the occurrence of environmentally released micro- and nanoplastics in the human food production chain and their potential health impact. The currently used analytical techniques introduce a great bias in the knowledge, since they are only able to detect plastic particles well above the nanorange. We discuss the potential use of the very sensitive analytical techniques that have been developed for the detection and quantification of engineered nanoparticles. We recognize three possible toxic effects of plastic particles: first due to the plastic particles themselves, second to the release of persistent organic pollutant adsorbed to the plastics, and third to the leaching of additives of the plastics. The limited data on microplastics in foods do not predict adverse effect of these pollutants or additives. Potential toxic effects of microplastic particles will be confined to the gut. The potential human toxicity of nanoplastics is poorly studied. Based on our experiences in nanotoxicology we prioritized future research questions.

Abstract: Because of their large and widespread application,phthalates or phthalic acid esters (PAEs) are ubiquitous in all the environmental compartements. They have been widely detected throughout the worldwide environment. Indoor air where people spend 65!90% of their time is also highly contaminated by various PAEs released from plastics, consumer products as well as ambient suspended particulate matter. Because of their widespread application, PAEs are the most common chemicals that humans are in contact with daily. Based on various exposure mechanisms, including the ingestion of food, drinking water, dust/soil, air inhalation and dermal exposure the daily intake of PAEs may reach values as high as 70 μg/kg/day. PAEs are involved in endocrine disrupting effects, namely, upon reproductive physiology in different species of fish and mammals. They also present a variety of additional toxic effects for many other species including terrestrial and aquatic fauna and flora. Therefore, their presence in the environment has attracted considerable attention due to their potential impacts on ecosystem functioning and on public health. This paper is a synthesis of the extensive literature data on behavior, transport, fate and ecotoxicological state of PAEs in environmental matrices: air, water, sediment, sludge, wastewater, soil, and biota. First, the origins and physicochemical properties of PAEs that control the behavior, transport and fate in the environment are reviewed. Second, the compilation of data on transport and fate, adverse environmental and human health effects, legislation, restrictions, and ecotoxicological state of the environment based on PAEs is presented.

Abstract: Electrochemical processes have been extensively investigated for the removal of a range of organic and inorganic contaminants. The great majority of these studies were conducted using nitrate-, perchlorate-, sulfate-, and chloride-based electrolyte solutions. In actual treatment applications, organic and inorganic constituents may have substantial effects on the performance of electrochemical treatment. In particular, the outcome of electrochemical oxidation will depend on the concentration of chloride and bromide. Formation of chlorate, perchlorate, chlorinated, and brominated organics may compromise the quality of the treated effluent. A critical review of recent research identifies future opportunities and research needed to overcome major challenges that currently limit the application of electrochemical water treatment systems for industrial and municipal water and wastewater treatment. Given the increasing interest in decentralized wastewater treatment, applications of electrolytic systems for treat...

Abstract: Microplastics have been found in seas all over the world. We hypothesize that sea salts might contain microplastics, because they are directly supplied by seawater. To test our hypothesis, we collected 15 brands of sea salts, lake salts, and rock/well salts from supermarkets throughout China. The microplastics content was 550–681 particles/kg in sea salts, 43–364 particles/kg in lake salts, and 7–204 particles/kg in rock/well salts. In sea salts, fragments and fibers were the prevalent types of particles compared with pellets and sheets. Microplastics measuring less than 200 μm represented the majority of the particles, accounting for 55% of the total microplastics, and the most common microplastics were polyethylene terephthalate, followed by polyethylene and cellophane in sea salts. The abundance of microplastics in sea salts was significantly higher than that in lake salts and rock/well salts. This result indicates that sea products, such as sea salts, are contaminated by microplastics. To the best of ...

Abstract: Ambient fine particulate matter (PM2.5) has a large and well-documented global burden of disease. Our analysis uses high-resolution (10 km, global-coverage) concentration data and cause-specific integrated exposure-response (IER) functions developed for the Global Burden of Disease 2010 to assess how regional and global improvements in ambient air quality could reduce attributable mortality from PM2.5. Overall, an aggressive global program of PM2.5 mitigation in line with WHO interim guidelines could avoid 750 000 (23%) of the 3.2 million deaths per year currently (ca. 2010) attributable to ambient PM2.5. Modest improvements in PM2.5 in relatively clean regions (North America, Europe) would result in surprisingly large avoided mortality, owing to demographic factors and the nonlinear concentration-response relationship that describes the risk of particulate matter in relation to several important causes of death. In contrast, major improvements in air quality would be required to substantially reduce mort...

Abstract: This research was designed for the first time to investigate the activities of photocatalytic composite, Ag3PO4/g-C3N4, in converting CO2 to fuels under simulated sunlight irradiation. The composite was synthesized using a simple in situ deposition method and characterized by various techniques including Brunauer–Emmett–Teller method (BET), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV–vis diffuse reflectance spectroscopy (DRS), photoluminescence spectroscopy (PL), and an electrochemical method. Thorough investigation indicated that the composite consisted of Ag3PO4, Ag, and g-C3N4. The introduction of Ag3PO4 on g-C3N4 promoted its light absorption performance. However, more significant was the formation of heterojunction structure between Ag3PO4 and g-C3N4, which efficiently promoted the separation of electron–hole pairs by a Z-scheme mechanism and ultimately ...

Abstract: Composting is widely used for recycling of urban sewage sludge to improve soil properties, which represents a potential pathway of spreading antibiotic resistant bacteria and genes to soils. However, the dynamics of antibiotic resistance genes (ARGs) and the underlying mechanisms during sewage sludge composting were not fully explored. Here, we used high-throughput quantitative PCR and 16S rRNA gene based illumina sequencing to investigate the dynamics of ARGs and bacterial communities during a lab-scale in-vessel composting of sewage sludge. A total of 156 unique ARGs and mobile genetic elements (MGEs) were detected encoding resistance to almost all major classes of antibiotics. ARGs were detected with significantly increased abundance and diversity, and distinct patterns, and were enriched during composting. Marked shifts in bacterial community structures and compositions were observed during composting, with Actinobacteria being the dominant phylum at the late phase of composting. The large proportion ...

Abstract: This study investigated the effects of metals (Fe3+, Cu2+, Ni2+, and Zn2+) and phenolic compounds (PCs: hydroquinone, catechol, and phenol) loaded on biomass on the formation of persistent free radicals (PFRs) in biochar. It was found that metal and phenolic compound treatments not only increased the concentrations of PFRs in biochar but also changed the types of PFRs formed, which indicated that manipulating the amount of metals and PCs in biomass may be an efficient method to regulate PFRs in biochar. These results provided direct evidence to elucidate the mechanism of PFR formation in biochar. Furthermore, the catalytic ability of biochar toward persulfate activation for the degradation of contaminants was evaluated. The results indicated that biochar activates persulfate to produce sulfate radicals (SO4•–) and degraded polychlorinated biphenyls (PCBs) efficiently. It was found that both the concentration and type of PFRs were the dominant factors controlling the activation of persulfate by biochar and...

Abstract: Magnetic CuO-Fe3O4 composite was fabricated by a simple hydrothermal method and characterized as a heterogeneous catalyst for phenol degradation. The effects of pH and bicarbonate ions on catalytic activity were extensively evaluated in view of the practical applications. The results indicated that an increase of solution pH and the presence of bicarbonate ions were beneficial for the removal of phenol in the CuO-Fe3O4 coupled with persulfate (PS) process. Almost 100% mineralization of 0.1 mM phenol can be achieved in 120 min by using 0.3 g/L CuO-Fe3O4 and 5.0 mM PS at pH 11.0 or in the presence of 3.0 mM bicarbonate. The positive effect of bicarbonate ion is probably due to the suppression of copper leaching as well as the formation of Cu(III). The reuse of catalyst at pH0 11.0 and 5.6 showed that the catalyst remains a high level of stability at alkaline condition (e.g., pH0 11.0). On the basis of the characterization of catalyst, the results of metal leaching and EPR studies, it is suggested that pheno...

Abstract: Cellulose nanomaterials are naturally occurring with unique structural, mechanical and optical properties. While the paper and packaging, automotive, personal care, construction, and textiles industries have recognized cellulose nanomaterials' potential, we suggest cellulose nanomaterials have great untapped potential in water treatment technologies. In this review, we gather evidence of cellulose nanomaterials' beneficial role in environmental remediation and membranes for water filtration, including their high surface area-to-volume ratio, low environmental impact, high strength, functionalizability, and sustainability. We make direct comparison between cellulose nanomaterials and carbon nanotubes (CNTs) in terms of physical and chemical properties, production costs, use and disposal in order to show the potential of cellulose nanomaterials as a sustainable replacement for CNTs in water treatment technologies. Finally, we comment on the need for improved communication and collaboration across the myriad industries invested in cellulose nanomaterials production and development to achieve an efficient means to commercialization.

Abstract: Nitrogen modified reduced graphene oxide (N-RGO) was prepared by a hydrothermal method. The nitrogen modification enhanced its adsorption and catalysis ability. For an initial bisphenol concentration of 0.385 mmol L–1, the adsorption capacity of N-RGO was evaluated as 1.56 and 1.43 mmol g–1 for bisphenol A (BPA) and 1.43 mmol g–1 for bisphenol F (BPF), respectively, both of which were about 1.75 times that (0.90 and 0.84 mmol g–1) on N-free RGO. N-RGO could activate persulfate, producing strong oxidizing sulfate radicals. The apparent degradation rate constant of BPA on N-RGO was 0.71 min–1, being about 700 times that (0.001 min–1) on N-free RGO. In mixtures of various phenols, the degradation rate constant of each phenol was linearly increased with its adsorption capacity. A simultaneous use of N-RGO and persulfate yielded fast and efficient removal of bisphenols. The use of N-RGO (120 mg L–1) and persulfate (0.6 mmol L–1) almost completely removed the added bisphenols (0.385 mmol L–1) at pH 6.6 within 1...

Abstract: In this work, simultaneous generation of hydroxyl radical (•OH) and sulfate radical (SO4•–) by the reaction of ozone (O3) with peroxymonosulfate (PMS; HSO5–) has been proposed and experimentally verified. We demonstrate that the reaction between the anion of PMS (i.e., SO52–) and O3 is primarily responsible for driving O3 consumption with a measured second order rate constant of (2.12 ± 0.03) × 104 M–1 s–1. The formation of both •OH and SO4•– from the reaction between SO52– and O3 is confirmed by chemical probes (i.e., nitrobenzene for •OH and atrazine for both •OH and SO4•–). The yields of •OH and SO4•– are determined to be 0.43 ± 0.1 and 0.45 ± 0.1 per mol of O3 consumption, respectively. An adduct, –O3SOO– + O3 → –O3SO5–, is assumed as the first step, which further decomposes into SO5•– and O3•–. The subsequent reaction of SO5•– with O3 is proposed to generate SO4•–, while O3•– converts to •OH. A definition of Rct,•OH and Rct,SO4•– (i.e., respective ratios of •OH and SO4•– exposures to O3 exposure) is ...

Abstract: The role of gut bacteria of mealworms (the larvae of Tenebrio molitor Linnaeus) in polystyrene (PS) degradation was investigated. Gentamicin was the most effective inhibitor of gut bacteria among six antibiotics tested. Gut bacterial activities were essentially suppressed by feeding gentamicin food (30 mg/g) for 10 days. Gentamicin-feeding mealworms lost the ability to depolymerize PS and mineralize PS into CO2, as determined by characterizing worm fecula and feeding with (13)C-labeled PS. A PS-degrading bacterial strain was isolated from the guts of the mealworms, Exiguobacterium sp. strain YT2, which could form biofilm on PS film over a 28 day incubation period and made obvious pits and cavities (0.2-0.3 mm in width) on PS film surfaces associated with decreases in hydrophobicity and the formation of C-O polar groups. A suspension culture of strain YT2 (10(8) cells/mL) was able to degrade 7.4 ± 0.4% of the PS pieces (2500 mg/L) over a 60 day incubation period. The molecular weight of the residual PS pieces was lower, and the release of water-soluble daughter products was detected. The results indicated the essential role of gut bacteria in PS biodegradation and mineralization, confirmed the presence of PS-degrading gut bacteria, and demonstrated the biodegradation of PS by mealworms.

Abstract: Polystyrene (PS) is generally considered to be durable and resistant to biodegradation. Mealworms (the larvae of Tenebrio molitor Linnaeus) from different sources chew and eat Styrofoam, a common PS product. The Styrofoam was efficiently degraded in the larval gut within a retention time of less than 24 h. Fed with Styrofoam as the sole diet, the larvae lived as well as those fed with a normal diet (bran) over a period of 1 month. The analysis of fecula egested from Styrofoam-feeding larvae, using gel permeation chromatography (GPC), solid-state (13)C cross-polarization/magic angle spinning nuclear magnetic resonance (CP/MAS NMR) spectroscopy, and thermogravimetric Fourier transform infrared (TG-FTIR) spectroscopy, substantiated that cleavage/depolymerization of long-chain PS molecules and the formation of depolymerized metabolites occurred in the larval gut. Within a 16 day test period, 47.7% of the ingested Styrofoam carbon was converted into CO2 and the residue (ca. 49.2%) was egested as fecula with a limited fraction incorporated into biomass (ca. 0.5%). Tests with α (13)C- or β (13)C-labeled PS confirmed that the (13)C-labeled PS was mineralized to (13)CO2 and incorporated into lipids. The discovery of the rapid biodegradation of PS in the larval gut reveals a new fate for plastic waste in the environment.

Abstract: Plastic debris is a prolific contaminant effecting freshwater and marine ecosystems across the globe. Of growing environmental concern are “microplastics”and “nanoplastics” encompassing tiny particles of plastic derived from manufacturing and macroplastic fragmentation. Pelagic zooplankton are susceptible to consuming microplastics, however the threat posed to larvae of commercially important bivalves is currently unknown. We exposed Pacific oyster (Crassostrea gigas) larvae (3–24 d.p.f.) to polystyrene particles spanning 70 nm-20 μm in size, including plastics with differing surface properties, and tested the impact of microplastics on larval feeding and growth. The frequency and magnitude of plastic ingestion over 24 h varied by larval age and size of polystyrene particle (ANOVA, P < 0.01), and surface properties of the plastic, with aminated particles ingested and retained more frequently (ANOVA, P < 0.01). A strong, significant correlation between propensity for plastic consumption and plastic load pe...

Abstract: Just as graphene triggered a new gold rush, three-dimensional graphene-based macrostructures (3D GBM) have been recognized as one of the most promising strategies for bottom-up nanotechnology and become one of the most active research fields during the last four years. In general, the basic structural features of 3D GBM, including its large surface area, which enhances the opportunity to contact pollutants, and its well-defined porous structure, which facilitates the diffusion of pollutant molecules into the 3D structure, enable 3D GBM to be an ideal material for pollutant management due to its excellent capabilities and easy recyclability. This review aims to describe the environmental applications and mechanisms of 3D GBM and provide perspective. Thus, the excellent performance of 3D GBM in environmental pollutant adsorption, transformation and detection are reviewed. Based on the structures and properties of 3D GBM, the removal mechanisms for dyes, oils, organic solvents, heavy metals, and gas pollutants are highlighted. We attempt to establish "structure-property-application" relationships for environmental pollution management using 3D GBM. Approaches involving tunable synthesis and decoration to regulate the micro-, meso-, and macro-structure and the active sites are also reviewed. The high selectivity, fast rate, convenient management, device applications and recycling utilization of 3D GBM are also emphasized.

Abstract: The adsorption and desorption of U(VI) on graphene oxides (GOs), carboxylated GOs (HOOC-GOs), and reduced GOs (rGOs) were investigated by batch experiments, EXAFS technique, and computational theoretical calculations. Isothermal adsorptions showed that the adsorption capacities of U(VI) were GOs > HOOC-GOs > rGOs, whereas the desorbed amounts of U(VI) were rGOs > GOs > HOOC-GOs by desorption kinetics. According to EXAFS analysis, inner-sphere surface complexation dominated the adsorption of U(VI) on GOs and HOOC-GOs at pH 4.0, whereas outer-sphere surface complexation of U(VI) on rGO was observed at pH 4.0, which was consistent with surface complexation modeling. Based on the theoretical calculations, the binding energy of [G···UO2]2+ (8.1 kcal/mol) was significantly lower than those of [HOOC-GOs···UO2]2+ (12.1 kcal/mol) and [GOs-O···UO2]2+ (10.2 kcal/mol), suggesting the physisorption of UO22+ on rGOs. Such high binding energy of [GOs-COO···UO2]+ (50.5 kcal/mol) revealed that the desorption of U(VI) from...

Abstract: Atrazine, propazine, and terbuthylazine are chlorotriazine herbicides that have been frequently used in agriculture and thus are potential drinking water contaminants. Hydroxyl radicals produced by advanced oxidation processes can degrade these persistent compounds. These herbicides are also very reactive with sulfate radicals (2.2-3.5 × 10(9) M(-1) s(-1)). However, the dealkylated products of chlorotriazine pesticides are less reactive toward sulfate radicals (e.g., desethyl-desisopropyl-atrazine (DEDIA; 1.5 × 10(8) M(-1) s(-1))). The high reactivity of the herbicides is largely due to the ethyl or isopropyl group. For example, desisopropyl-atrazine (DIA) reacts quickly (k = 2 × 10(9) M(-1) s(-1)), whereas desethyl-atrazine (DEA) reacts more slowly (k = 9.6 × 10(8) M(-1) s(-1)). The tert-butyl group does not have a strong effect on reaction rate, as shown by the similar second order reaction rates between desethyl-terbuthylazine (DET; k = 3.6 × 10(8) M(-1) s(-1)) and DEDIA. Sulfate radicals degrade a significant proportion of atrazine (63%) via dealkylation, in which deethylation significantly dominates over deisopropylation (10:1). Sulfate and hydroxyl radicals react at an equally fast rate with atrazine (k (hydroxyl radical + atrazine) = 3 × 10(9) M(-1) s(-1)). However, sulfate and hydroxyl radicals differ considerably in their reaction rates with humic acids (k (sulfate radical + humic acids) = 6.8 × 10(3) L mgC(-1) s(-1) (mgC = mg carbon); k (hydroxyl radical + humic acids) = 1.4 × 10(4) L mgC(-1) s(-1)). Thus, in the presence of humic acids, atrazine is degraded more efficiently by sulfate radicals than by hydroxyl radicals.

Abstract: To achieve efficient photocatalytic air purification, we constructed an advanced semimetal–organic Bi spheres–g-C3N4 nanohybrid through the in-situ growth of Bi nanospheres on g-C3N4 nanosheets. This Bi–g-C3N4 compound exhibited an exceptionally high and stable visible-light photocatalytic performance for NO removal due to the surface plasmon resonance (SPR) endowed by Bi metal. The SPR property of Bi could conspicuously enhance the visible-light harvesting and the charge separation. The electromagnetic field distribution of Bi spheres involving SPR effect was simulated and reaches its maximum in close proximity to the Bi particle surface. When the Bi metal content was controlled at 25%, the corresponding Bi–g-C3N4 displayed outstanding photocatalytic capability and transcended those of other visible-light photocatalysts. The Bi–g-C3N4 exhibited a high structural stability under repeated photocatalytic runs. A new visible-light-induced SPR-based photocatalysis mechanism with Bi–g-C3N4 was proposed on the ...

Abstract: The use of nanoparticles in consumer products, for example, cosmetics, sunscreens, and electrical devices, has increased tremendously over the past decade despite insufficient knowledge about their effects on human health and ecosystem function. Moreover, the amount of plastic waste products that enter natural ecosystems, such as oceans and lakes, is increasing, and degradation of the disposed plastics produces smaller particles toward the nano scale. Therefore, it is of utmost importance to gain knowledge about how plastic nanoparticles enter and affect living organisms. Here we have administered 24 and 27 nm polystyrene nanoparticles to fish through an aquatic food chain, from algae through Daphnia, and studied the effects on behavior and metabolism. We found severe effects on feeding and shoaling behavior as well as metabolism of the fish; hence, we conclude that polystyrene nanoparticles have severe effects on both behavior and metabolism in fish and that commonly used nanosized particles may have considerable effects on natural systems and ecosystem services derived from them.

Abstract: We here first proposed a yolk-shell Co3O4@metal-organic frameworks (MOFs) nanoreactor via a facile method to accommodate sulfate radical-based advanced oxidation processes (SR-AOPs) into its interior cavity. The mesoporous and adsorptive MOFs shells allow the rapid diffusion of reactant molecules to the encapsulated Co3O4 active sites, and the confined high instantaneous concentration of reactants in the local void space is anticipated to facilitate the SR-AOPs. As a proof of concept, the nanoreactor was fully characterized and applied for catalytic degradation of 4-chlorophenol (4-CP) in the presence of peroxymonosulfate (PMS). The enhancement of SR-AOPs in the nanoreactor is demonstrated by the result that degradation efficiency of 4-CP reached almost 100% within 60 min by using the yolk-shell Co3O4@MOFs catalysts as compared to only 59.6% under the same conditions for bare Co3O4 NPs. Furthermore, the applicability of this nanoreactor used in SR-AOPs was systematically investigated in terms of effect of reaction parameters and identification of intermediates and primary radical as well as mineralization of the reaction and stability of the composite. The findings of this study elucidated a new opportunity for improved environmental remediation.

Abstract: The addition of iron is a convenient way for removing phosphorus from wastewater, but this is often considered to limit phosphorus recovery. Struvite precipitation is currently used to recover phosphorus, and this approach has attracted much interest. However, it requires the use of enhanced biological phosphorus removal (EBPR). EBPR is not yet widely applied and the recovery potential is low. Other phosphorus recovery methods, including sludge application to agricultural land or recovering phosphorus from sludge ash, also have limitations. Energy-producing wastewater treatment plants increasingly rely on phosphorus removal using iron, but the problem (as in current processes) is the subsequent recovery of phosphorus from the iron. In contrast, phosphorus is efficiently mobilized from iron by natural processes in sediments and soils. Iron–phosphorus chemistry is diverse, and many parameters influence the binding and release of phosphorus, including redox conditions, pH, presence of organic substances, and...

Abstract: Microscopic plastic fragments (<5 mm) are a worldwide conservation issue, polluting both coastal and marine environments. Fibers are the most prominent plastic type reported in the guts of marine organisms, but their effects once ingested are unknown. This study investigated the fate of polypropylene rope microfibers (1–5 mm in length) ingested by the crab Carcinus maenas and the consequences for the crab’s energy budget. In chronic 4 week feeding studies, crabs that ingested food containing microfibers (0.3–1.0% plastic by weight) showed reduced food consumption (from 0.33 to 0.03 g d–1) and a significant reduction in energy available for growth (scope for growth) from 0.59 to −0.31 kJ crab d–1 in crabs fed with 1% plastic. The polypropylene microfibers were physically altered by their passage through the foregut and were excreted with a smaller overall size and length and amalgamated into distinctive balls. These results support of the emerging paradigm that a key biological impact of microplastic inges...

Abstract: Adsorption of 4-n-nonylphenol (4-n-NP) and bisphenol A (BPA) on magnetic reduced graphene oxides (rGOs) as a function of contact time, pH, ionic strength and humic acid were investigated by batch techniques. Adsorption of 4-n-NP and BPA were independent of pH at 3.0- 8.0, whereas the slightly decreased adsorption was observed at pH 8.0–11.0. Adsorption kinetics and isotherms of 4-n-NP and BPA on magnetic rGOs can be satisfactorily fitted by pseudo-second-order kinetic and Freundlich model, respectively. The maximum adsorption capacities of magnetic rGOs at pH 6.5 and 293 K were 63.96 and 48.74 mg/g for 4-n-NP and BPA, respectively, which were significantly higher than that of activated carbon. Based on theoretical calculations, the higher adsorption energy of rGOs + 4-n-NP was mainly due to π–π stacking and flexible long alkyl chain of 4-n-NP, whereas adsorption of BPA on rGOs was energetically favored by a lying-down configuration due to π–π stacking and dispersion forces, which was further demonstrated ...

Abstract: Dissolved organic matter (DOM) is known to form strong complexes with heavy metals and thus governs the distribution, toxicity, bioavailability, and ultimate fate of heavy metals in the environment. The relevant aspects of metal-organic interactions remain unclear because the metal binding functionalities in DOM are substantially nonuniform and the availability of the models is limited. In this work, two-dimensional correlation spectroscopy (2DCOS) integrated with synchronous fluorescence and infrared absorption spectroscopy was used to explore the binding process of copper to DOM. A series of heterogeneous binding sites in humic acid (HA), a representative DOM, and the subsequent subtle changes of these sites within the molecular interactions were elucidated by the 2DCOS method. The band assignments and the correspondence between the results obtained by two spectral probes (synchronous fluorescence and infrared absorption spectra) were verified by hetero-2DCOS. Our results showed that, during the copper binding process, the carboxyl and polysaccharide groups gave the fastest responses to copper binding. Then fluorescence quenching of fluorescent humic-like moieties occurred with a vibrational change of the related functionalities, i.e., phenolic and aryl carboxylic groups, which further induces the fluorescence quenching of fulvic-like fractions. Finally, small amounts of amide and aliphatic groups participated in the copper binding after the fluorescence of the protein-like fraction decreased. With these promising results, a comprehensive picture of structural changes of HA during the copper binding process was developed, highlighting the superior potential of 2D heterospectral correlation spectroscopy in studying complex interactions in the environment.