TL;DR: In this paper, a throughflow model of salt accumulation in the Western Australian wheatbelt is introduced and tested by field observations and data from several locations, and the results demonstrate that soluble salts move from the catchments to the valley bottoms by a combination of the following processes.
Abstract: Summary A throughflow model of salt accumulation in the Western Australian wheatbelt is introduced and tested by field observations and data from several locations. Areas of excessive soil salinity (salt scalds) in the York-Mawson area are associated with specific soil/geomorphic conditions. Thirty-eight scalds and their catchments were examined: of these ten were mapped in detail and 100 soil profiles in 15 catenary sequences were examined and described. Valley-side slopes of the gently rolling landscape are low-angled, with the modal slopes of the 15 catenas ranging between 1.2 and 3.5 degrees. Interfluves are characterised by sand-textured soils that overlie lateritic duricrust or gravels at varying depths. Valley-sides above the salt scalds are predominantly erosional/transportational landsurface units with a sharp decrease of soil permeability at about plough depth. Further marked reductions in permeability and hence water infiltration occur at greater depth. The salt scalds vary considerably in size (0.02 to 64.4 ha) and nearly all are located in valley bottoms. The latter are usually occupied by well defined stream channels with ephemeral streamflow regimes, and all salt scalds occur on predominantly colluvial and/or alluvial aggradational soil materials. The layering of these materials produces one or more perched soil-water tables at relatively shallow depths below the scald surfaces, and impermeable hardpans occur below the aggradational soil materials. Four areas were examined in detail in the Dalwallinu area, where salt scalding is virtually continuous along the floors of the wide, flat valley bottoms. The results demonstrate that soluble salts move from the catchments to the valley bottoms by a combination of the following processes: (1) occasional overland flow; (2) throughflow, at varying depths below the surface, generally concentrated in percolines; and (3) streamflow down minor tributaries, this streamflow being fed by a combination of (1) and (2). The water supplied to the valley bottoms by these cascades is prevented from percolating to deeper levels by a thick impermeable hardpan which, in turn, also comprises the upper, confining material of the deeper-seated aquifer system in which groundwater is under pressure. Surface or near-surface waterlogging of the valley bottoms is essentially a shallow, perched water phenomenon. Evaporation during summer concentrates the salts in the valley bottom soil materials, leading to very high salinity levels. The water inputs responsible for the increased extent and duration of saturation of scalded soils since clearing appear to be derived primarily from an increase in throughflow and less from overland flow. A successful attempt at salt scald rehabilitation and recent drilling in other parts of the wheatbelt provide further evidence in support of the throughflow model of salt accumulation. An implication of these findings is that valley-side interception of throughflow should result in substantial rehabilitation of many salt scalds in the Western Australian wheatbelt.
TL;DR: An interesting flow phenomenon in a cross-flow impeller, an asymmetrical throughflow in a geometrically symmetrical impeller has been investigated experimentally as mentioned in this paper, and the causes of the throughflow are explained in relation to the flow mechanisms.
Abstract: An interesting flow phenomenon in a cross-flow impeller --- an asymmetrical throughflow in a geometrically symmetrical impeller --- has been investigated experimentally. The causes of the throughflow are explained in relation to the flow mechanisms. Flow was visualized by moire method of topography and solid particles. The transient process of the flow from the starting of an impeller until formation of a large eccentric vortex was observed in details. If Reynolds number is larger than 250, the throughflow occurs in all the types of the impellers experimented. In the steady rotation of the impeller the eccentric vortex rotates slowly around the impeller-axis and flow pattern changes sequentially. The change of flow patterns is essential to the flow of the cross-flow impellers.
TL;DR: In this article, an electrical throughflow heater is constructed such that it receives at least one further functional element and/or partially surrounds it, and a shape-on-profile shank(s) with two shanks and the wall forming a U.
Abstract: Electrical throughflow heater has throughflow pipe(s) and an electrical heating body, parallel to each other and in heat-conducting mutual connection. The wall of one of these functional elements is constructed such that it receives at least one further functional element and/or partially surrounds it. Pref. an endless profile is used, as a double or multiple pipe, whose wall parts act directly as jacket for the electric heating body, and which has a shaped-on profile shank(s), which may be L-shaped, with two shanks and the wall forming a U. No welding or soldering is needed.
TL;DR: In this article, an analysis of the flow between two infinitely large corotating disks with throughflow supplied at the inner periphery of finite radius is made, where the flow field is assumed to be either everywhere laminar or everywhere turbulent.
Abstract: In order to obtain fundamental knowledge of performance and optimum dimensions of a disk friction pump, an analysis is made of the flow between two infinitely large corotating disks with throughflow supplied at the inner periphery of finite radius. The flow field is assumed to be either everywhere laminar or everywhere turbulent. The laminar case is treated by dividing the field into three regions; the region in the vicinity of the entrance periphery to which Gortler series is applied, the region far from the center axis for which analytical perturbation solution is used and the mid-region connecting the above two extreme regions for which finite difference computation is carried out. The solution gives a complete scheme of the flow field with satisfactory indications for the engineering scheme of the flow field with satisfactory indications for the engineering purpose. Meanwhile, the turbulent case is treated by means of momentum equations with elaborated curvilinear coordinate axes, which leads to a physically acceptable flow pattern.
TL;DR: In this paper, a throughflow heater with thermal control and with switchable electric heating elements has the water outlet temp fluctuating about a reference value, and the fluctuations are equalized by switching the heating bodies with a regulator which has set switch-on and switch-off temperatures which are different.
Abstract: Throughflow heater with thermal control and with switchable electric heating elements has the water outlet temp. fluctuating about a reference value. The fluctuations are equalized by switching the heating bodies with a regulator which has set switch-on and switch-off temperatures which are different. The regulator with the highest switch-on temperature has the lowest switch-off temperature; that with the lowest switch-on temperature has the lowest switch-off temperature; that with the lowest switch-on temperature has the highest switch-on temperature; and the others have corresponding average temperatures all pref. symmetrically about the reference value. Switching is minimised.
TL;DR: In this article, a through-flow water heater has heating bodies in throughflow water pipes which are connected to each other by channels and lie parallel to them, and are of equal lengths.
Abstract: Throughflow water heater has heating bodies in throughflow water pipes which are connected to each other by channels and lie parallel to them, and are of equal lengths. The pipes and channels are formed from a one-piece pipe block, closed at each end by a cover flange. Preferably the block is of A1, or of a temp.-stable plastics; the pipes and channels are interconnected by perforations or by apertures in the flanges, which are plastics injection moulded parts and contain additional measuring and regulating appts. for the heater, e.g. differential press. switches, or constant flow controller(s). The pipes are easily produced, connected and mounted.