Polycaprolactone

Abstract: Polycaprolactone (PCL) is an important polymer due to its mechanical properties, miscibility with a large range of other polymers and biodegradability. Two main pathways to produce polycaprolactone have been described in the literature: the polycondensation of a hydroxycarboxylic acid: 6-hydroxyhexanoic acid, and the ring-opening polymerisation (ROP) of a lactone: e-caprolactone (e-CL). This critical review summarises the different conditions which have been described to synthesise PCL, and gives a broad overview of the different catalytic systems that were used (enzymatic, organic and metal catalyst systems). A surprising variety of catalytic systems have been studied, touching on virtually every section of the periodic table. A detailed list of reaction conditions and catalysts/initiators is given and reaction mechanisms are presented where known. Emphasis is put on the ROP pathway due to its prevalence in the literature and the superior polymer that is obtained. In addition, ineffective systems that have been tried to catalyse the production of PCL are included in the electronic supplementary information for completeness (141 references).

Abstract: A number of different processing techniques have been developed to design and fabricate three-dimensional (3D) scaffolds for tissue-engineering applications. The imperfection of the current techniques has encouraged the use of a rapid prototyping technology known as fused deposition modeling (FDM). Our results show that FDM allows the design and fabrication of highly reproducible bioresorbable 3D scaffolds with a fully interconnected pore network. The mechanical properties and in vitro biocompatibility of polycaprolactone scaffolds with a porosity of 61 +/- 1% and two matrix architectures were studied. The honeycomb-like pores had a size falling within the range of 360 x 430 x 620 microm. The scaffolds with a 0/60/120 degrees lay-down pattern had a compressive stiffness and a 1% offset yield strength in air of 41.9 +/- 3.5 and 3.1 +/- 0.1 MPa, respectively, and a compressive stiffness and a 1% offset yield strength in simulated physiological conditions (a saline solution at 37 degrees C) of 29.4 +/- 4.0 and 2.3 +/- 0.2 MPa, respectively. In comparison, the scaffolds with a 0/72/144/36/108 degrees lay-down pattern had a compressive stiffness and a 1% offset yield strength in air of 20.2 +/- 1.7 and 2.4 +/- 0.1 MPa, respectively, and a compressive stiffness and a 1% offset yield strength in simulated physiological conditions (a saline solution at 37 degrees C) of 21.5 +/- 2.9 and 2.0 +/- 0.2 MPa, respectively. Statistical analysis confirmed that the five-angle scaffolds had significantly lower stiffness and 1% offset yield strengths under compression loading than those with a three-angle pattern under both testing conditions (p < or = 0.05). The obtained stress-strain curves for both scaffold architectures demonstrate the typical behavior of a honeycomb structure undergoing deformation. In vitro studies were conducted with primary human fibroblasts and periosteal cells. Light, environmental scanning electron, and confocal laser microscopy as well as immunohistochemistry showed cell proliferation and extracellular matrix production on the polycaprolactone surface in the 1st culturing week. Over a period of 3-4 weeks in a culture, the fully interconnected scaffold architecture was completely 3D-filled by cellular tissue. Our cell culture study shows that fibroblasts and osteoblast-like cells can proliferate, differentiate, and produce a cellular tissue in an entirely interconnected 3D polycaprolactone matrix.

Abstract: The aim of this review is to show the relationships between the structure, the process, and the properties of biodegradable multiphase systems based on plasticized starch (PLS), the so‐called “thermoplastic starch.” These mutiphase materials are obtained when associating association between plasticized starches and other biodegradable materials, such as biodegradable polyesters [polycaprolactone (PCL), polyhydroxyalkanoates (PHAs), polylactic acid (PLA), polyesteramide (PEA), aliphatic, and aromatic copolyesters], or agro‐materials (ligno‐cellulosic fiber, lignin etc.). Depending on materials (soft, rigid) and the plastic processing system used, various structures (blends, composites, multilayers) can be obtained. The compatibility problematic between these hetero‐materials is analyzed. These starchy products show some interesting properties and have some applications in different fields: packaging, sports, catering, agriculture and gardening, or hygiene.