Abstract: Development in the textile industry leads to an increased demand for the use of various dyes. Moreover, there is the use of some dyes in the food industry as well as medical diagnostics. Thereby, increased demand for dyes in various fields has resulted in dye-containing wastewater. Only a small portion of the generated wastewater is adequately treated. The rest is usually dumped or otherwise directly discharged into the sewage system, which ultimately enters rivers, lakes, and streams. The handling and disposal of such concentrated wastewater, especially the dye-containing wastewater, is considered to be a major environmental issue from the moment of its generation to its ultimate disposal. Conventional water treatment methods such as flotation, filtration, adsorption, etc., are non-destructive physical separation processes. They only transfer the pollutants to other phases, thereby generating concentrated deposits. The advanced oxidation process (AOP) is one of the most effective emerging methods for the treatment of wastewater containing chemical pollutants. The method involves the formation and interaction of highly reactive hydroxyl radicals under suitable activation conditions. These radicals are non-selective and efficient for the destruction and eventual mineralization of recalcitrant organic pollutants. This review aims at the pros and cons of using photocatalysis as an efficient AOP to degrade dye-containing wastewater.

Abstract: The use of nonrenewable fossil fuels for energy has increased in recent decades, posing a serious threat to human life. As a result, it is critical to build environmentally friendly and low-cost reliable and renewable energy storage solutions. The supercapacitor is a future energy device because of its higher power density and outstanding cyclic stability with a quick charge and discharge process. Supercapacitors, on the other hand, have a lower energy density than regular batteries. It is well known that the electrochemical characteristic of supercapacitors is strongly dependent on electrode materials. The current review highlights advance in the TMOs for supercapacitor electrodes. In addition, the newly discovered hybrid/pseudo-supercapacitors have been discussed. Metal oxides that are employed as electrode materials are the focus of this study. The discovery of nanostructured electrode materials continues to be a major focus of supercapacitor research. To create high-performance electrode materials from a morphological standpoint, various efforts have been attempted. Lastly, we analyze the supercapacitor’s evolving trend and our perspective for the future generations of supercapacitors.

Abstract: This review addresses research and development on the use of ionic liquids as extractants and diluents in the solvent extraction of metals. Primary attention is given to the efficiency and selectivity of metal extraction from industrial wastewater with ionic liquids composed of various cations and anions. The review covers literature sources published in the period of 2010–2021. The bibliography includes 98 references dedicated to research on the extraction and separation of lanthanides (17 sources), actinides (5 sources), heavy metals (35 sources), noble metals, including the platinum group (16 sources), and some other metals.

Abstract: Carbon dioxide is a byproduct of our industrial society. It is released into the atmosphere, which has an adverse effect on the environment. Carbon dioxide management is necessary to limit the global average temperature increase to 1.5 degrees Celsius and mitigate the effects of climate change, as outlined in the Paris Agreement. To accomplish this objective realistically, the emissions gap must be closed by 2030. Additionally, 10–20 Gt of CO2 per year must be removed from the atmosphere within the next century, necessitating large-scale carbon management strategies. The present procedures and technologies for CO2 carbonation, including direct and indirect carbonation and certain industrial instances, have been explored in length. This paper highlights novel technologies to capture CO2, convert it to other valuable products, and permanently remove it from the atmosphere. Additionally, the constraints and difficulties associated with carbon mineralization have been discussed. These techniques may permanently remove the CO2 emitted due to industrial society, which has an unfavorable influence on the environment, from the atmosphere. These technologies create solutions for both climate change and economic development.

Abstract: This study seeks to evaluate the economic implication of a biogas digester built from composite material to ascertain its cost effectiveness. The feasibility study conducted indicates that a brick made only of fixed dome digester costs between USD 3193.99 and USD 4471.59. This high cost is attributed to the construction material, thus prompting the need to use materials of lower cost for affordability and sustainability. Hence, the digester under study was made from composite material comprising high-density polyethylene (HDPE), bricks and cement. The inlet and outlet chambers were built using bricks and cement, while the digestion chamber was made from HDPE material. From the economic analysis conducted, the total initial investment cost of the biogas digester was reported to be USD 1623.41 with an internal rate of return (IRR) of 8.5%, discount payback period (DPP) of 2 years and net present value (NPV) of USD 1783.10. The findings equally revealed that the estimated quantity of biogas could replace 33.2% of liquefied petroleum gas (LPG) cooking gas. Moreover, the biogas daily yield of 1.57 m3 generates approximately 9.42 kWh of electricity, which costs about USD 1.54. Thus, the study recommends the use of composite material of plastics and bricks in constructing the biogas digester, as it is cost effective and sustainable.

Abstract: In the present work, based on numerical simulation, a comparative analysis of the flow of a chemically reacting gas flow through a catalyst is performed using the example of selective hydrogenation of acetylene in a wide range of flow temperatures variation. Catalyst models are based on open-cell foam material. A comparison is also made with calculations and experimental data for a granular catalyst. The porosity and cell diameter were chosen as variable parameters for the porous catalyst. The results of numerical studies were obtained in the form of component concentration fields of the gas mixture, vector fields of gas movement, values of conversion, and selectivity of the reaction under study. The parameters of the porous material of the catalyst are determined for the maximum efficiency of the process under study.

Abstract: Quinazoline is an essential scaffold, known to be linked with various biological activities. Some of the prominent biological activities of this system are analgesic, anti-inflammatory, anti-hypertensive, anti-bacterial, anti-diabetic, anti-malarial, sedative–hypnotic, anti-histaminic, anti-cancer, anti-convulsant, anti-tubercular, and anti-viral activities. This diversity in the pharmacological response of the quinazoline system has encouraged medicinal chemists to study and discover this system and its multitude of potential against several biological activities. Many of these studies have successfully investigated the structure–activity relationship to explore the specific structural features of their biological targets. The developing understanding of quinazoline derivatives and their biological targets presents opportunities for the discovery of novel therapeutics. This review represents different aspects of medicinal chemistry, including drug design, structure–activity relationship, and the mode of action of some analgesic and anti-inflammatory quinazoline compounds. It pays comprehensive attention to the analgesic and anti-inflammatory activities of quinazolines from the viewpoint of drug discovery and its development.

Abstract: A standard CO2 capture process is implemented in Aspen HYSYS, simulated, and evaluated based on available data from Fortum’s waste burning facility at Klemetsrud in Norway. Since amine-based CO2 removal has high costs, the main aim is cost-optimizing. A simplified carbon-capture unit with a 20-m absorber packing height, 90% CO2 removal efficiency, and a minimum approach temperature for the lean/rich amine heat exchanger (ΔTmin) of 10 °C was considered the base case simulation model. A sensitivity analysis was performed to optimize these parameters. For the base case study, CO2 captured cost was calculated as 37.5 EUR/t. When the sensitivity analysis changes the size, the Power Law method adjusts the equipment cost. A comparison of the Enhanced Detailed Factor (EDF) and the Power Law approach was performed for all simulations to evaluate the uncertainties in the findings from the Power Law method. The optimums calculated for ΔTmin and CO2 capture rate were 15 °C and 87% for both methods, with CO2 removal costs of 37 EUR/t CO2 and 36.7 EUR/t CO2, respectively. With 19 m of packing height to absorber, the minimum CO2 capture cost was calculated as 37.3 EUR/t and 37.1 EUR/t for the EDF and Power Law methods, respectively. Since there was a difference between the Power Law method and the EDF method, a size factor exponent derivation was performed. The derivation resulted in the following exponents: for the lean heat exchanger 0.74, for the lean/rich heat exchanger 1.03, for the condenser 0.68, for the reboiler 0.92, for the pump 0.88, and for the fan 0.23.

Abstract: Sector coupling remains a crucial measure to achieve climate change mitigation targets. Hydrogen and Power-to-X (PtX) products are recognized as major levers to allow the boosting of renewable energy capacities and the consequent use of green electrons in different sectors. In this work, the challenges presented by the PtX processes are addressed and different process intensification (PI) strategies and their potential to overcome these challenges are reviewed for ammonia (NH3), dimethyl ether (DME) and oxymethylene dimethyl ethers (OME) as three exemplary, major PtX products. PI approaches in this context offer on the one hand the maximum utilization of valuable renewable feedstock and on the other hand simpler production processes. For the three discussed processes a compelling strategy for efficient and ultimately maintenance-free chemical synthesis is presented by integrating unit operations to overcome thermodynamic limitations, and in best cases eliminate the recycle loops. The proposed intensification processes offer a significant reduction of energy consumption and provide an interesting perspective for the future development of PtX technologies.

Abstract: Adsorption systems are characterized by challenging behavior to simulate any numerical method. A novel field of study emerged within the numerical method in the last two years: the physics-informed neural network (PINNs), the application of artificial intelligence to solve partial differential equations. This is a complete new standpoint for solving engineering first-principle models, which up to that date was not explored in the field of adsorption systems. Therefore, this work proposed the evaluation of PINN to address the numerical solutions of a fixed-bed column where a monoclonal antibody is purified. The PINNs solution is compared with a traditional numerical method. The results show the accuracy of the proposed PINNs when compared with the numerical method. This points towards the potential of this technique to address complex numerical problems found in chemical engineering.

Abstract: In this work, the authors aimed to identify a potential correlation between the printability and crucial rheological characteristics of materials involved in fused deposition modeling (FDM) technology. In this regard, three different poly(lactide) acid (PLA)-based filaments (two commercially available (here called V-PLA and R-PLA) and one processed in a lab-scale extruder (here called L-PLA)) have been considered. Dynamic rheological testing, in terms of frequency sweep at five different temperatures (130, 150, 170, 190, and 210 °C), was performed. Rheological properties expressed in terms of viscoelastic moduli and complex viscosity curves vs. frequency, characteristic relaxation times, activation energy (Ea), zero shear viscosity (η0) and shear thinning index (n) were derived for each material. A characteristic relaxation time of around 0.243 s was found for V-PLA, a similar value (0.295 s) was calculated for R-PLA filaments, and a lower value of about an order of magnitude was calculated for L-PLA filament (~0.0303 s). The activation energy and shear thinning index resulted to be very comparable for all the filaments. On the contrary, V-PLA and R-PLA possessed a zero-shear viscosity (~104 Pa*s at 170 °C) much higher than L-PLA (~103 Pa*s). All the filaments were processed in a 3D printer, by attesting the effect of nozzle temperature (180, 190, and 210 °C, respectively) on printing process, and macroscopic shaping defects in printed objects. Final considerations allowed us to conclude that polymer relaxation time, zero-shear viscosity, and melt viscosity (affected by printing temperature) were critical parameters affecting the printing quality.

Abstract: This study aims to synthesize Au/TiO2/Na2Ti6O13 composites to reduce the occurrence of recombination and increase photocatalytic activity in phenol degradation. Gold was used due to its high stability and strong surface plasmon resonance (SPR) properties which make it operate effectively in the visible light spectrum. The prepared composites were characterized using XRD, SEM, TEM, FTIR, and DRS. The results showed that the composite consisted of rutile TiO2 with a crystal size of 38–40 nm and Na2Ti6O13 with a crystal size of 25 nm. The gold in the composite has a crystallite size of 16–19 nm along with the percentage of gold added. Morphological analysis shows that the composite has the form of inhomogeneous spherical particles with gold spread among composites with sizes less than 20 nm. FTIR analysis showed the presence of Na–O and Ti–O–Ti bonds in the composite. The best composite was 3% Au/TiO2/Na2Ti6O13 which had high crystallinity, small particle size, and bandgap energy of 2.59 eV. Furthermore, it had an efficiency 205% better than without gold. After that, cost estimation is proposed as a large-scale application. This study describes the total cost, break-even analysis, and payback analysis for the commercialization needs of the designed photocatalytic catalyst.

Abstract: Garlic (Allium sativum L.) is an herbaceous plant and is recognised for its numerous medicinal and culinary properties, and it is used in diverse food preparations for its characteristic flavour and aroma. High alliin content increases the formation of allicin, a bioactive compound of garlic. Therefore, this research aimed to compare different extraction methods for garlic (Allium sativum L.) between subcritical water extraction (SWE) and Soxhlet extraction to obtain a high extraction yield and alliin content. The SWE conditions were 120 °C and 180 °C temperatures and 2 mL/min and 6 mL/min flow rates at a constant pressure of 15 MPa for a 10 min extraction time, respectively. In the meanwhile, the extraction time for Soxhlet extraction with various solvents, namely, distilled water, ethanol–water (1:1), and 100% ethanol, was two hours. High-performance liquid chromatography (HPLC) was used to analyse alliin. Soxhlet extraction had the best yield (1.96 g) using ethanol–water (1:1) as the solvent in comparison to SWE extraction (1.28 g) at 180 °C and 6 mL/min. In contrast, SWE yielded a greater concentration of alliin (136.82 mg/g) at 120 °C and 2 mL/min than the Soxhlet method when using distilled water as the solvent (65.18 mg/g). Therefore, SWE may replace Soxhlet extraction as the conventional method for extracting alliin from garlic at a high concentration, and SWE has advantages that favour garlic extracts.

Abstract: The microwave setup for obtaining plasma-activated water (PAW) has been created. PAW contains significant concentrations of H2O2 and NO3−, has a reduced content of O2, high conductivity, a high redox potential and low pH. Likewise, the specific electrical conductivity and concentration of H2O2 and NO3− linearly depend on the treatment time. These parameters are simple and convenient markers for controlling the preparation of PAW. It has been established that PAW solutions with a concentration of 0.5–1.0% increase the germination energy, protect against fusarium and hyperthermia in cotton, wheat and strawberry seeds. In addition, PAWs have a positive effect on the growth rate of plants in the early stages of development. The use of PAW provides significant benefits over the chemical preparations Dalbron and Bakhor, so-called seed germination stimulators (SDS).

Abstract: At present, the trend towards partial replacement of petroleum-derived fuels by those from the revaluation of biomass has become of great importance. An effective strategy for processing complex biomass feedstocks involves prior conversion to simpler compounds (platform molecules) that are more easily transformed in subsequent reactions. This study analyzes the metal–organic frameworks (MOFs) that contain Zr metal clusters formed by ligands of terephthalic acid (UiO-66) and aminoterephthalic acid (UiO-66-NH2), as active and stable catalysts for the esterification of levulinic acid with methanol. An alternative synthesis is presented by means of ultrasonic stirring at room temperature and 60 °C, in order to improve the structural properties of the catalysts. They were analyzed by X-ray diffraction, scanning electron microscopy, infrared spectroscopy, X-ray photoelectron spectroscopy, microwave plasma atomic emission spectroscopy, acidity measurement, and N2 adsorption. The catalytic reaction was carried out in a batch system and under pressure in an autoclave. Its progress was followed by gas chromatography and mass spectrometry. Parameters such as temperature, catalyst mass, and molar ratio of reactants were optimized to improve the catalytic performance. The MOF that presented the highest activity and selectivity to the desired product was obtained by synthesis with ultrasound and 60 °C with aminoterephthalic acid. The methyl levulinate yield was 67.77% in batch at 5 h and 85.89% in an autoclave at 1 h. An analysis of the kinetic parameters of the reaction is presented. The spent material can be activated by ethanol washing allowing the catalytic activity to be maintained in the recycles.

Abstract: In this study, the poisoning effects of cerium oxide (CeO2) as the contaminant on the performance of proton exchange membrane fuel cells (PEMFCs) are evaluated. An experimental setup was developed to analyze the performance characteristic (I-V) curves in contaminated and non-contaminated conditions. Focused ion-beam scanning electron microscopy (FIB-SEM) cross-section images were obtained as an input for the energy dispersive X-ray (EDX) analysis. The results of the EDX analysis verified the presence of CeO2 in the contaminated membrane electrode assembly (MEA), in addition to fluorine and sulfur. EDX analysis also revealed that as a result of CeO2 contamination, sulfur and fluorine would be distributed all around the MEA, instead of being only in the membrane. The results illustrate that hydrofluoric acid (HF), sulfuric acid (H2SO4), and fluorinated polymer fragments are released, which enhance the crossover of the reactant gases through the membrane, hence reducing the cell’s performance. The I-V characteristic curves proved that the non-contaminated PEMFC setup had double the performance of the contaminated PEMFC.

Abstract: Pesticide pollution is a major issue, given their intensive use in the 20th century, which led to their accumulation in the environment. At the international level, strict regulations are imposed on the use of pesticides, simultaneously with the increasing interest of researchers from all over the world to find methods of neutralizing them. Photocatalytic degradation is an intensively studied method to be applied for the degradation of pesticides, especially through the use of solar energy. The mechanisms of photocatalysis are studied and implemented in pilot and semi-pilot installations on experimental platforms, in order to be able to make this method more efficient and to identify the equipment that can achieve the photodegradation of pesticides with the highest possible yields. This paper proposes a brief review of the impact of pesticides on the environment and some techniques for their degradation, with the main emphasis on different photoreactor configurations, using slurry or immobilized photocatalysts. This review highlights the efforts of researchers to harmonize the main elements of photocatalysis: choice of the photocatalyst, and the way of photocatalyst integration within photoreaction configuration, in order to make the transfer of momentum, mass, and energy as efficient as possible for optimal excitation of the photocatalyst.

Abstract: Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Various fuel cells have been proposed, of which proton-exchange membrane fuel cells (PEMFC) and solid oxide fuel cells (SOFC) are the most frequently used. However, experimental testing rigs are expensive, and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of the operation of fuel cells is compulsory to avoid damage, and such control must be based on accurate models, able to predict cell behaviour and prevent stresses and shutdown. Additionally, when used for mobile applications, intrinsically dynamic operation is needed. Some selected examples of steady-state, dynamic and fluid-dynamic modelling of different types of fuel cells are here proposed, mainly dealing with PEMFC and SOFC types. The general ideas behind the thermodynamic, kinetic and transport description are discussed, with some examples of models derived for single cells, stacks and integrated power cogeneration units. This review can be considered an introductory picture of the modelling methods for these devices, to underline the different approaches and the key aspects to be taken into account. Examples of different scales and multi-scale modelling are also provided.

Abstract: The synthesis and applications of composites based on layered double hydroxides (LDHs) and nanocarbons have recently seen great development. On the one hand, LDHs are versatile 2D compounds that present a plethora of applications, from medicine to energy conversion, environmental remediation, and heterogeneous catalysis. On the other, nanocarbons present unique physical and chemical properties owing to their low-dimensional structure and sp2 hybridization of carbon atoms, which endows them with excellent charge carrier mobility, outstanding mechanical strength, and high thermal conductivity. Many reviews described the applications of LDH/nanocarbon composites in the areas of energy and photo- and electro-catalysis, but there is still scarce literature on their latest applications as heterogeneous catalysts in chemical synthesis and conversion, which is the object of this review. First, the properties of the LDHs and of the different types of carbon materials involved as building blocks of the composites are summarized. Then, the synthesis methods of the composites are described, emphasizing the parameters allowing their properties to be controlled. This highlights their great adaptability and easier implementation. Afterwards, the application of LDH/carbon composites as catalysts for C–C bond formation, higher alcohol synthesis (HAS), oxidation, and hydrogenation reactions is reported and discussed in depth.

Abstract: In this work, basalt fibers (BF) have been investigated as possible natural and sustainable replacements for the common synthetic mineral filler—glass fibers (GF)—used in polyamide 66 matrix (PA66). Composites have been prepared at two different fiber concentrations (15 and 25 wt.%, respectively) by melt blending. The developed systems have been mainly characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), capillary rheology, and scanning electron microscopy (SEM). The kinetic parameters to thermal degradation through the Coats–Redfern method allowed us to attest a negligible effect of fiber type on thermal stability of the developed systems. Composites incorporating 15 wt.% of fiber content possessed the highest activation energy (≥230 kJ/mol). The introduction of BF and GF in PA 66 polymer, regardless of content, always led to an increase in crystallization and melting temperatures, and to a similar reduction in crystallinity degree and glass transition temperature. The shear viscosity of the basic polymer increased by the addition of fillers, particularly at low shear rate, with a pronounced effect in the case of basal fibers. A slightly higher shear thinning behavior of BF/PA66 with respect to GF/PA66 composites was confirmed by fitting the flow curves through the power law model. Finally, a worsening in fiber dispersion, by increasing the content in the matrix, and a weak compatibility between the two phases constituting the materials were highlighted through SEM micrographs.

Abstract: Sewage sludge is here studied as a valuable source for processing or energy conversation thanks to its high nutrition and energy content. However, various origins of the wastewater, different water cleaning technologies, and seasonal and regional dependencies lead to the high variability of the sewage sludge properties. In thermal treatment units, that is, incineration, gasification and pyrolysis, sewage sludge serves as feedstock or fuel, hence a proper characterization and a mathematical description of the sewage sludge are required to estimate product streams and to formulate numerical simulations and optimization methods. The presented work introduces a surrogate concept that allows replication of sewage sludge’s ultimate composition, moisture, and ash content. The surrogate approach aims to model the decomposition of any sewage sludge sample, opposite to the established determination of kinetic rates for individual samples. Based on chemical solid surrogate species and corresponding reaction mechanisms, the thermal decomposition path is described. Sewage sludge is represented by a combination of lignocellulosic species, proteins, sugars, lipids, and representative inorganic species. The devolatilization and heterogeneous reactions are formulated such that they can be used together with a detailed gas-phase model, including tar oxidation and emission models for nitrogen and sulfur oxides, recently proposed by the authors. The developed chemical model is applied using a zero-dimensional gasification reactor in order to model weight loss within the thermogravimetric analysis, pyrolysis, gasification and combustion conditions. Weight loss, the composition of product gases, and emission release (nitrogen and sulfur oxides) are captured well by the model. The flexible surrogate approach allows us to represent various sewage sludge samples.

Abstract: A rapid, facile, and environmentally benign strategy to electrochemical oxidation of metallic tungsten under pulse alternating current in an aqueous electrolyte solution was reported. Particle size, morphology, and electronic structure of the obtained WO3 nanopowders showed strong dependence on electrolyte composition (nitric, sulfuric, and oxalic acid). The use of oxalic acid as an electrolyte provides a gram-scale synthesis of WO3 nanopowders with tungsten electrochemical oxidation rate of up to 0.31 g·cm−2·h−1 that is much higher compared to the strong acids. The materials were examined as photoanodes in photoelectrochemical reforming of organic substances under solar light. WO3 synthesized in oxalic acid is shown to exhibit excellent activity towards the photoelectrochemical reforming of glucose and ethylene glycol, with photocurrents that are nearly equal to those achieved in the presence of simple alcohol such as ethanol. This work demonstrates the promise of pulse alternating current electrosynthesis in oxalic acid as an efficient and sustainable method to produce WO3 nanopowders for photoelectrochemical applications.

Abstract: In recent decades, the environmental impact caused by greenhouse gases, especially CO2, has driven many countries to reduce the concentration of these gases. The study and development of new designs that maximise the efficiency of CO2 capture continue to be topical. This paper presents a review of the application of hydrotalcites as CO2 sinks. There are several parameters that can make hydrotalcites suitable for use as CO2 sinks. The first question is the use of calcined or uncalcined hydrotalcite as well as the temperature at which it is calcined, since the calcination conditions (temperature, rate and duration) are important parameters determining structure recovery. Other aspects were also analysed: (i) the influence of the pH of the synthesis; (ii) the molar ratio of its main elements; (iii) ways to increase the specific area of hydrotalcites; (iv) pressure, temperature, humidity and time in CO2 absorption; and (v) combined use of hydrotalcites and cement-based materials. A summary of the results obtained so far in terms of CO2 capture with the parameters described above is presented. This work can be used as a guide to address CO2 capture with hydrotalcites by showing where the information gaps are and where researchers should apply their efforts.

Abstract: Pyrolysis is a low-emission and sustainable thermochemical technique used in the production of biofuels, which can be used as an alternative to fossil fuels. Understanding the kinetic characterization of biomass pyrolysis is essential for process upscaling and optimization. There is no accepted model that can predict pyrolysis kinetics over a wide range of pyrolysis conditions and biomass types. This study investigates whether or not the classical lumped kinetic model with a three-competitive reaction scheme can accurately predict the walnut shell pyrolysis product yields. The experimental data were obtained from walnut shell pyrolysis experiments at different temperatures (300–600 °C) using a fixed-bed reactor. The chosen reaction scheme was in good agreement with our experimental data for low temperatures, where the primary degradation of biomass occurred (300 and 400 °C). However, at higher temperatures, there was less agreement with the model, indicating that some other reactions may occur at such temperatures. Hence, further studies are needed to investigate the use of detailed reaction schemes to accurately predict the char, tar, and gas yields for all types of biomass pyrolysis.

Abstract: Photocatalytic hydrogen production was studied with a formic acid solution with titanium dioxide (TiO2) with the aid of simultaneous Rh deposition. The optimum conditions were as follows: Rh loading, 0.1 wt%; formic acid concentration, 1.0%; solution, pH 2.2; temperature, 50 °C. Under the optimum conditions, the photocatalytic hydrogen production with TiO2 by the simultaneous deposition of Rh was 5.0 mmol g−1, 12.2 mmol g−1 and 16.0 mmol g−1 after 1 h, 3 h and 5 h of irradiation time for black light, respectively. Rh/TiO2 photocatalysts were characterized by XRD, SEM, photoluminescence spectra, diffuse reflectance spectra and the BET surface area. The reaction mechanism of photocatalytic hydrogen production from formic acid by Rh/TiO2 was also proposed.

Abstract: The amount of precipitate and residue affects the timing of fuel filter blockage. This study develops a model for fuel filter blocking based on the Precipitate Measurement. Firstly, a modification of ASTM D 7501 for the Cold Soak Filtration Test (CSFT) measured the amount of precipitate in B20 fuel with variations of soaking temperatures and monoglyceride content in biodiesel. Then, a modified ASTM D 2068 for a filter blocking test (FBT) was conducted to correlate the impurities in the B20 fuel and the clogging limit effects represented by the change of pressure difference and time to reach a pressure drop of 30 kPa. Biodiesel B20 samples were prepared by adding monopalmitin so that each had a monoglyceride value of 0.2%, 0.4%, 0.6%, and 0.8% before blending with petroleum diesel. The modified CSFT showed that the amount of B0 impurity was almost zero. However, the amount of the B20 sample precipitate retained on the filter was higher when a lower soaking temperature and higher monoglyceride content was used in the biodiesel. Similar results in the modified FBT showed that the more impurities, the faster the pressure drop achieved a level of 30 kPa. A much shorter time was needed to reach the pressure drop of 30 kPa for B20 fuel samples with the impurities present in both test powders and precipitate compared to those for the B20 fuel samples with a single type of impurity (either test powders or precipitate). The fuel filter clogging time could also be predicted using the graph of fuel filter clogging time vs. the precipitate weight of B20 fuel derived from the FBT test if the precipitate weight had already been determined by the precipitation test (modified CSFT). The simulation model using Ergun’s equation for the FBT of the B20 fuel could also show similar results to that of the FBT experiment, with the difference (averaged errors) ranging from 4.15% to 5.79%.

Abstract: Hydrotalcite is the name of a mineral discovered in Sweden in 1842 whose formula is Mg6Al2(OH)16CO3·4H2O and presents a layered crystal structure that consists of positively charged hydroxide layers neutralized by interlayer anions as carbonate, also containing water molecules. The ease of their synthesis and the possibility of incorporating other layer cations and interlayer anions have made this type of layered double hydroxides (LDH) a group of very interesting materials for industry. In addition to LDH and due to the name of the most representative mineral, this group of compounds is commonly called hydrotalcite-like materials, or simply hydrotalcites. Another way of referring to them is as anionic clays because of their layered structure but, unlike classical clays, their layers are positive and their interlayers are anionic. The main fields of application of these solids comprise catalysis, catalyst support, anion scavengers, polymer stabilizers, drug carriers, or adsorbents. This paper briefly summarizes some of the work carried out by Professor Rives over more than thirty years, focused, among other topics, on the study of the synthesis, characterization, and applications of hydrotalcites. This research has led him to train many researchers, to collaborate with research groups around the world and to publish reference papers and books in this field. This contribution, written to be included in the Special Issue “A Themed Issue in Honor of Prof. Dr. Vicente Rives”, edited on the occasion of his retirement, only shows a small part of his scientific research and intends to value and recognize his cleverness and his enormous scientific and human quality.

Abstract: Consumers’ interest in a high-quality healthy diet is creating a growing trend in the food industry, focusing on the design and development of new products rich in bioactive compounds. This work involves the formulation of a vegetable sauce obtained from a mixture of pumpkin and pepper, the study of the evolution of bioactive compounds, quality and sensory parameters during storage at 4 and 25 °C, the influence of the packaging materials (PVC, PE/PA, and PS), and the migration degree. Antioxidant activity, polyphenols, carotenoids, and brown pigments contents were studied at 25 °C. Overall migration of the containers and the evolution of the physicochemical parameters and sensory attributes of the sauce were analyzed. All plastic materials showed an overall migration lower than the limit of EU and Mercosur Regulations. PVC better preserved polyphenols, antioxidant activity, and carotenoids until 50, 10, and 30 days, respectively, and lower development of brown pigments was observed. Higher storage temperatures favored undesirable changes in sensory attributes before 50 days of storage. PVC can be used to achieve greater conservation of the sensory attributes of sauce, regardless of the storage temperature. It could be considered the best material to preserve the bioactive properties and sensory attributes of the sauce until 30 days.

Abstract: Nonionic surfactants are reported as being able to enhance enzyme stability and increase the conversion of enzymatic reactions. Surfactant-assisted enzymatic hydrolysis conversion is affected by surfactant HLB values. This work investigated the influence of nonionic surfactants with different HLB values on chitosan enzymatic hydrolysis using cellulase enzyme by measuring the reducing sugars formation, viscosity, and molecular weight of hydrolyzed chitosan. A characterization analysis of hydrolyzed products was also carried out. A higher HLB value exhibits a better enzymatic chitosan hydrolysis performance, shown by the decrease in a solution’s viscosity and the increase in reducing sugar formation. Increasing the surfactant concentration will also increase the hydrolysis rate. Nonionic surfactants can protect cellulase enzyme from the denaturation of temperature and stirring influence. The higher the HLB value, the lower the molecular weight of the hydrolyzed chitosan. The result of UV–Vis demonstrated aldehyde groups formation during hydrolysis. The SEM analysis showed that the chitosan, hydrolyzed using different HLB values of surfactants, had different surface morphologies. However, it did not change the chemical structure of the hydrolysis product seen by the FTIR analysis. The XRD patterns showed that the relative crystallinity of raw chitosan decreased when hydrolyzed with surfactants.