https://hal.archives-ouvertes.fr/hal-03176982/document

Adding a protective screw improves hinge's axial and torsional stability in High Tibial Osteotomy

Background Alignment correction of the lower limb by medial open-wedge high tibial osteotomy (HTO) is an efficient technique, but loss of correction and hardware failure can occur owing to inadequate fixation. A surgical technique using opposite screw insertion was previously applied for salvage of the lateral hinge fracture, but evidence for its utility as a protective strategy was unclear. Methods Finite element models were reconstructed using artificial bone models, commercial bone plate, and locking screws in the HTO model. The 6.5-mm cancellous or 6.5/8.0-mm pretensioned lag screw was virtually inserted from the opposite cortex to the medial tibial plateau. Testing loads were applied for simulating standing and initial sit-to-stand postures. The axial displacement of the posteromedial tibial plateau, which represents the loss of the posteromedial tibial plateau in clinical observation, and stresses on the bone plate, locking screws, and opposite screws were evaluated. Results Pretensioned lag screw insertion effectively reduced the loss of posteromedial reduction compared with the HTO model without opposite screw insertion [6.5-mm lag screw, by 50.8% (standing)/56.3% (sit-to-stand); 8.0-mm lag screws, by 51.9% (standing)/57.5% (sit-to-stand); normalised by the performance in the intact model]. The noncompressed opposite cancellous screw slightly reduced the stresses on the bone plate and screws, but did not contribute to the control of reduction loss at the posteromedial tibial plateau. Stresses on screws were lower than those on the corresponding bone plates, so the risk of screw breakage may be low. Conclusion The present study revealed that pretensioned opposite lag screw insertion is a simple and effective technique to improve the structural stability in medial open-wedge HTO. Further biomechanical and clinical verification will be required to enhance user confidence in this technique. The translational potential of this article The efficacy and advantages of additional opposite lag screw insertion in medial wedge high tibial osteotomy surgery have been described in this current study by a virtual biomechanical evaluation. Basing on this observation, it would worth further clinical trials for clarification and verification in reality.

Benefits of opposite screw insertion technique in medial open-wedge high tibial osteotomy: A virtual biomechanical study.

This article presents an experimental approach to the geometrical planning of the medial opening wedge high tibial osteotomy surgery which, as it is known, is an efficient surgical strategy quite widely used in treating knee osteoarthritis. While most of the published papers focus on analyzing this surgery from a medical point of view, we suggest a postoperative experimental evaluation of the intervention from a biomechanical point of view. The geometrical planning and, more specifically, the determination of the point of intersection between the corrected mechanical axis and the medial-lateral articular line of the knee, is a problem quite often debated in literature. This paper aims to experimentally investigate the behavior of the tibia with an open wedge osteotomy fixed with a locking plate, TomoFix (DE Puy Synthes), taking into account two positions of the mechanical axis of the leg on the width of the tibial plateau, measured from medial to lateral at 50% and 62.5% (Fujisawa point), respectively. The variations of the force relative to the deformation, strains, and displacements resulting from the progressive loading of the tibial plateau are studied. The research results reveal that using the Fujisawa point is better for conducting the correction not only for medical reasons, but also from a mechanical point of view.

/pdf/geometrical-planning-of-the-medial-opening-wedge-high-tibial-25dcreaw.pdf

Geometrical Planning of the Medial Opening Wedge High Tibial Osteotomy—An Experimental Approach

Abstract Proximal humeral shaft fractures can be treated with helically deformed bone plates to reduce the risk of iatrogenic nerve lesion. Controversially to this common surgical technique that was first established in 1999, no biomechanical investigation on humeral helical plating is recorded by other reviews, which focus on proximal fractures exclusively. Does an additional scope for shaft fractures reveal findings of helical testing? The present systematic literature review was performed based on guidelines by Kitchenham et al. to systematically search and synthesize literature regarding biomechanical testing of osteosynthetic systems for proximal humeral shaft fractures. Therefore, a systematic approach to search and screen literature was defined beforehand and applied on the findings of the database PubMed®. Synthesized information of the included literature was categorized, summarized and analyzed via descriptive statistics. Out of 192 findings, 22 publications were included for qualitative synthesis. A wide range of different test methods was identified, leading to a suboptimal comparability of specific results between studies. Overall, 54 biomechanical test scenarios were identified and compared. Physiological based boundary conditions (PB-BC) were referenced in 7 publications only. One study of testing straight and helical dynamic compression plates without PB-BCs was identified, showing significant differences under compressional loading. The absence of test standards of specific fields like humeral fractures lead to a high variance in biomechanical testing of osteosynthetic locking plates for proximal humeral shaft fractures. Physiological approaches offer realistic test scenarios but need to be uniformed for enhanced comparability between studies. The impact of helically deformed locking plates under PB-BC was not identified in literature.

Biomechanical testing of osteosynthetic locking plates for proximal humeral shaft fractures – a systematic literature review

Background The supplemental screw technique was introduced for salvage of lateral hinge fracture in medial open-wedge high tibial osteotomy (owHTO). The efficacy of its use in protection of lateral hinge fracture and corresponding biomechanical behaviors remained unclear. The current study was aimed to clarify if a supplemental screw can provide better protection to lateral hinge in biomechanical perspective. Materials An in vitro biomechanical test was conducted. Tibial sawbones, commercial owHTO plates and a cannulated screw were utilized for preparing the intact, owHTO, and owHTO with cannulated screw insertion specimens. A "staircase" dynamic load protocol was adopted for axial compressive test with increasing load levels to determine structural strength and durability by using a material testing system, while a motion capture system was applied for determining the dynamic changes in varus angle and posterior slope of the tibia plateau with various specimen preparation conditions. Results Type II lateral hinge fracture were the major failure pattern in all specimens prepared with owHTO. The insertion of a supplemental cannulated screw in medial owHTO specimens reinforced structural stability and durability in dynamic cyclic loading tests: the compressive stiffness increased to 58.9-62.2% of an intact specimen, whereas the owHTO specimens provided only 23.7-29.2% of stiffness of an intact specimen. In view of tibial plateau alignment, the insertion of a supplemental screw improved the structural deficiency caused by owHTO, and reduced the posterior slope increase and excessive varus deformity by 81.8% and 83.2%, respectively. Conclusion The current study revealed that supplemental screw insertion is a simple and effective technique to improve the structural stability and durability in medial owHTO.

/pdf/a-supplemental-screw-enhances-the-biomechanical-stability-in-15zjch42xu.pdf

A supplemental screw enhances the biomechanical stability in medial open-wedge high tibial osteotomy.

Biomechanical properties following open wedge high tibial osteotomy: Plate fixator combined with dynamic locking screws versus standard locking screws

Angular stable implants reduced the complication rate in the treatment of humeral head fractures. But the failure rate is still high. To further reduce the risk of cut-out, cement augmentation of screws was introduced. A reason for failure of plate osteosynthesis might be the extremely high stiffness of the screw-plate interface leading to a loss of reduction and cut-out of screws. A more homogeneous distribution of the forces on all screws may avoid secondary dislocation. We hypothesize that dynamic osteosynthesis minimizes screw loosening and results in a higher load to failure than standard locking screws. Twelve paired human humerus specimens were analysed. A standardized three-part fracture model with a metaphyseal defect was simulated. Within each pair of humeri, one was fixed with a Philos plate and standard locking screws (LS), whereas the other humerus was fixed with a Philos plate and dynamic locking screws (DLS). A cyclic varus-bending test or a rotation test with increasing loading force was performed until failure of the screw-bone-fixation. In the varus bending test, pairs failed by screw loosening in the humeral head. The LS-group reached 2901 (601–5201) load cycles until failure, while the DLS-group failed after 3731 (2001–5601) cycles. This corresponds to a median loading of 195 N for the LS-group and 235 N for the DLS-group (p = 0.028). In the rotation test the LS-group reached a median of 1101 (501–1501) load cycles until failure of fixation occurred, while the DLS-group failed after 1401 (401–2201) cycles (p = 0.225). Plate fixation using dynamic locking screws for the treatment of proximal humerus fractures demonstrated more load cycles until failure compared to standard locking plate osteosynthesis.

/pdf/dynamic-locking-screws-in-proximal-humeral-plate-56npw4opny.pdf

Dynamic locking screws in proximal humeral plate osteosynthesis demonstrate superior fixation properties: a biomechanical study

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

Thomas Freude

Author Tools

Chat about Author

Papers

Biomechanical properties following open wedge high tibial osteotomy: Plate fixator combined with dynamic locking screws versus standard locking screws

Dynamic locking screws in proximal humeral plate osteosynthesis demonstrate superior fixation properties: a biomechanical study