Two-photon excitation provides a means of activating chemical or physical processes with high spatial resolution in three dimensions and has made possible the development of three-dimensional fluorescence imaging, optical data storage, and lithographic microfabrication. These applications take advantage of the fact that the two-photon absorption probability depends quadratically on intensity, so under tight-focusing conditions, the absorption is confined at the focus to a volume of order λ3 (where λ is the laser wavelength). Any subsequent process, such as fluorescence or a photoinduced chemical reaction, is also localized in this small volume. Although three-dimensional data storage and microfabrication have been illustrated using two-photon-initiated polymerization of resins incorporating conventional ultraviolet-absorbing initiators, such photopolymer systems exhibit low photosensitivity as the initiators have small two-photon absorption cross-sections (δ). Consequently, this approach requires high laser power, and its widespread use remains impractical. Here we report on a class of π;-conjugated compounds that exhibit large δ (as high as 1, 250 × 10−50 cm4 s per photon) and enhanced two-photon sensitivity relative to ultraviolet initiators. Two-photon excitable resins based on these new initiators have been developed and used to demonstrate a scheme for three-dimensional data storage which permits fluorescent and refractive read-out, and the fabrication of three-dimensional micro-optical and micromechanical structures, including photonic-bandgap-type structures.

Two-photon polymerization initiators for three-dimensional optical data storage and microfabrication

Fogging occurs when moisture condensation takes the form of accumulated droplets with diameters larger than 190 nm or half of the shortest wavelength (380 nm) of visible light. This problem may be effectively addressed by changing the affinity of a material’s surface for water, which can be accomplished via two approaches: i) the superhydrophilic approach, with a water contact angle (CA) less than 5°, and ii) the superhydrophobic approach, with a water CA greater than 150°, and extremely low CA hysteresis. To date, all techniques reported belong to the former category, as they are intended for applications in optical transparent coatings. A well-known example is the use of photocatalytic TiO2 nanoparticle coatings that become superhydrophilic under UV irradiation. Very recently, a capillary effect was skillfully adopted to achieve superhydrophilic properties by constructing 3D nanoporous structures from layer-by-layer assembled nanoparticles. The key to these two “wet”-style antifogging strategies is for micrometer-sized fog drops to rapidly spread into a uniform thin film, which can prevent light scattering and reflection from nucleated droplets. Optical transparency is not an intrinsic property of antifogging coatings even though recently developed antifogging coatings are almost transparent, and the transparency could be achieved by further tuning the nanoparticle size and film thickness. To our knowledge, the antifogging coatings may also be applied to many fields that do not require optical transparency, including, for example, paints for inhibiting swelling and peeling issues and metal surfaces for preventing corrosion. These types of issues, which are caused by adsorption of moisture, are hard to solve by the superhydrophilic approach because of its inherently “wet” nature. Thus, a “dry”-style antifogging strategy, which consists of a novel superhydrophobic technique that can prevent moisture or microscale fog drops from nucleating on a surface, is desired. Recent bionic researches have revealed that the self-cleaning ability of lotus leaves and the striking ability of a water-strider’s legs to walk on water can be attributed to the ideal superhydrophobicity of their surfaces, induced by special microand nanostructures. To date, the biomimetic fabrication of superhydrophobic microand/or nanostructures has attracted considerable interest, and these types of materials can be used for such applications as self-cleaning coatings and stain-resistant textiles. Although a superhydrophobic technique inspired by lotus leaves is expected to be able to solve such fogging problems because the water droplets can not remain on the surface, there are no reports of such antifogging coatings. Very recently, researchers from General Motors have reported that the surfaces of lotus leaves become wet with moisture because the size of the fog drops are at the microscale—so small that they can be easily trapped in the interspaces among micropapillae. Thus, lotuslike surface microstructures are unsuitable for superhydrophobic antifogging coatings, and a new inspiration from nature is desired for solving this problem. In this communication, we report a novel, biological, superhydrophobic antifogging strategy. It was found that the compound eyes of the mosquito C. pipiens possess ideal superhydrophobic properties that provide an effective protective mechanism for maintaining clear vision in a humid habitat. Our research indicates that this unique property is attributed to the smart design of elaborate microand nanostructures: hexagonally non-close-packed (ncp) nipples at the nanoscale prevent microscale fog drops from condensing on the ommatidia surface, and hexagonally close-packed (hcp) ommatidia at the microscale could efficiently prevent fog drops from being trapped in the voids between the ommatidia. We also fabricated artificial compound eyes by using soft lithography and investigated the effects of microand nanostructures on the surface hydrophobicity. These findings could be used to develop novel superhydrophobic antifogging coatings in the near future. It is known that mosquitoes possess excellent vision, which they exploit to locate various resources such as mates, hosts, and resting sites in a watery and dim habitat. To better understand such remarkable abilities, we first investigated the interaction between moisture and the eye surface. An ultrasonic humidifier was used to regulate the relative humidity of the atmosphere and mimic a mist composed of numerous tiny water droplets with diameters less than 10 lm. As the fog was C O M M U N IC A IO N

The dry-style antifogging properties of mosquito compound eyes and artificial analogues prepared by soft lithography: a superhydrophobic state with high adhesive force

Bioinspired engineering of honeycomb structure – Using nature to inspire human innovation

This review gives an overview of recent advances in the potential applications of superhydrophobic materials. Such properties are characterized by extremely high water contact angles and various adhesion properties. The conception of superhydrophobic materials has been possible by studying and mimicking natural surfaces. Now, various applications have emerged such as anti-icing, anti-corrosion and anti-bacterial coatings, microfluidic devices, textiles, oil–water separation, water desalination/purification, optical devices, sensors, batteries and catalysts. At least two parameters were found to be very important for many applications: the presence of air on superhydrophobic materials with self-cleaning properties (Cassie–Baxter state) and the robustness of the superhydrophobic properties (stability of the Cassie–Baxter state). This review will allow researchers to envisage new ideas and industrialists to advance in the commercialization of these materials.

Recent advances in the potential applications of bioinspired superhydrophobic materials

Recent Advances in OLED Optical Design

A biologically inspired compound-eye structure, which composes of ~5,867 honeycomb-patterned microlenses, was fabricated on a hemispherical shell. The fabrication process was simple and low-cost, which involves a femtosecond laser-enhanced wet etching and casting process followed by a thermomechanical process to convert the film into a hemispherical surface. By optimizing the parameters of thermomechanical process to form the curvilinear surface, the experimental result shows that the microlenses are omnidirectionally aligned on the dome with lens diameters of ~85 µm and the angle between two lens of ~2°, and the individual microlenses have rudimentary focusing and imaging properties. The artificial compound-eye structure fabricated by this method has great potential applications in scale-invariant processing, robot vision, and fast motion detection.

A simple route to fabricate artificial compound eye structures.

This work reveals a cost-efficient and flexible approach to various microlens arrays on polymers, which is essential to micro-optics elements. An 800-nm femtosecond laser is employed to control the hydrofluoric (HF) acid etching process on silica glasses, and concave microstructures with smooth curved surfaces are produced by this method. Then, the micro-structured glass templates can serve as molds for replicating microlenses on polymers. In this paper, a high-ordered microlens array with over 16,000 hexagonal-shaped lenses is fabricated on poly (dimethyl siloxane) [PDMS], and its perfect light-gathering ability and imaging performance are demonstrated. The flexibility of this method is demonstrated by successful preparation of several concave molds with different patterns which are difficult to be obtained by other methods. This technique provides a new route to small-scaled, smooth and curved surfaces which is widely used in micro-optics, biochemical analysis and superhydrophobic interface.

Versatile route to gapless microlens arrays using laser-tunable wet-etched curved surfaces

Microlens arrays on curvilinear surfaces are highly desirable for wide field-of-view imaging and sensing systems. However, it is technically challenging to fabricate these structures. This letter reports a simple method to machine close-packed microlenses on curvilinear surfaces as inspired by the insect eyes, which involves a femtosecond-laser-based microfabrication and a thermomechanical bending process. Over 7600 hexagonal-shaped microlenses with a diameter of 50 μm were fabricated on a hemispherical poly (methyl methacrylate) shell, which is similar to the compound eyes of insects. The optical performances of the microlens array were demonstrated by the abilities of high-resolution imaging and large view-angle focusing.

Fabrication of bioinspired omnidirectional and gapless microlens array for wide field-of-view detections

We present a developed femtosecond laser enhanced wet chemical etching method to fabricate close-packed and high numerical aperture (NA) microlens arrays (MLAs). Its ability to fabricate 100% fill factor MLAs with controllable NA is demonstrated and the maximum NA value of the lenses reaches to 0.47. This letter provides a simple and efficient way to achieve controllable and low cost optical elements. The close-packed and high-NA properties lead to excellent optical performance of the MLAs, which are highly required in high-resolution and high-signal-to-noise-ratio detections in micro-optical and integrated optical applications.

A Simple Way to Fabricate Close-Packed High Numerical Aperture Microlens Arrays

Method for enhancing chemical etching through femtosecond laser to manufacture large-scale micro-lens array

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

Pubo Qu

Author Tools

Chat about Author