Graphene plasmons are rapidly emerging as a viable tool for fast electrical manipulation of light. The prospects for applications to electro-optical modulation, optical sensing, quantum plasmonics, light harvesting, spectral photometry, and tunable lighting at the nanoscale are further stimulated by the relatively low level of losses and high degree of spatial confinement that characterize these excitations compared with conventional plasmonic materials. We start with a general description of the plasmons in extended graphene, followed by analytical methods that lead to reasonably accurate estimates of both the plasmon energies and the strengths of coupling to external light in graphene nanostructures, including graphene ribbons. We discuss several possible strategies to extend these plasmons towards the visible and near infrared, including a reduction in the size of the graphene structures and an increase in the level of doping. Specifically, we discuss plasmons in narrow ribbons and molecular-size graphene structures. We further formulate prescriptions based on geometry to increase the level of electrostatic doping without causing electrical breakdown. Results are also presented for plasmons in highly-doped single-wall carbon nanotubes, which exhibit similar characteristics as narrow ribbons and show a relatively small dependence on the chirality of the tubes. We further discuss perfect light absorption by a single-atom carbon layer, which we illustrate by investigating arrays of ribbons using fully analytical expressions. Finally, we explore the possibility of exploiting optically pumped transient plasmons in graphene, whereby the optically heated graphene valence band can sustain collective plasmon oscillations similar to those of highly doped graphene, and well-defined during the picosecond time window over which the electron is at an elevated temperature.

Graphene Plasmonics: Challenges and Opportunities

Graphene plasmons are rapidly emerging as a viable tool for fast electrical manipulation of light. The prospects for applications to electro-optical modulation, optical sensing, quantum plasmonics, light harvesting, spectral photometry, and tunable lighting at the nanoscale are further stimulated by the relatively low level of losses and high degree of spatial confinement that characterize these excitations compared with conventional plasmonic materials, alongside the large nonlinear response of graphene. We start with a general description of the plasmonic behavior of extended graphene, followed by analytical methods that lead to reasonably accurate estimates of both the plasmon energies and the strengths of coupling to external light in graphene nanostructures, including graphene ribbons. Although graphene plasmons have so far been observed at mid-infrared and longer wavelengths, there are several possible strategies to extend them toward the visible and near-infrared, including a reduction in the size ...

Organic–inorganic metal halide perovskite solar cells were fabricated by laminating films of a carbon nanotube (CNT) network onto a CH3NH3PbI3 substrate as a hole collector, bypassing the energy-consuming vacuum process of metal deposition. In the absence of an organic hole-transporting material and metal contact, CH3NH3PbI3 and CNTs formed a solar cell with an efficiency of up to 6.87%. The CH3NH3PbI3/CNTs solar cells were semitransparent and showed photovoltaic output with dual side illuminations due to the transparency of the CNT electrode. Adding spiro-OMeTAD to the CNT network forms a composite electrode that improved the efficiency to 9.90% due to the enhanced hole extraction and reduced recombination in solar cells. The interfacial charge transfer and transport in solar cells were investigated through photoluminescence and impedance measurements. The flexible and transparent CNT network film shows great potential for realizing flexible and semitransparent perovskite solar cells.

Laminated Carbon Nanotube Networks for Metal Electrode-Free Efficient Perovskite Solar Cells

Abstract Monolithic all-perovskite tandem photovoltaics promise to combine low-cost and high-efficiency solar energy harvesting with the advantages of all-thin-film technologies. To date, laboratory-scale all-perovskite tandem solar cells have only been fabricated using non-scalable fabrication techniques. In response, this work reports on laser-scribed all-perovskite tandem modules processed exclusively with scalable fabrication methods (blade coating and vacuum deposition), demonstrating power conversion efficiencies up to 19.1% (aperture area, 12.25 cm 2 ; geometric fill factor, 94.7%) and stable power output. Compared to the performance of our spin-coated reference tandem solar cells (efficiency, 23.5%; area, 0.1 cm 2 ), our prototypes demonstrate substantial advances in the technological readiness of all-perovskite tandem photovoltaics. By means of electroluminescence imaging and laser-beam-induced current mapping, we demonstrate the homogeneous current collection in both subcells over the entire module area, which explains low losses (&lt;5% rel ) in open-circuit voltage and fill factor for our scalable modules. 

/pdf/scalable-two-terminal-all-perovskite-tandem-solar-modules-2rt8rqkp.pdf

Scalable two-terminal all-perovskite tandem solar modules with a 19.1% efficiency

Semiconducting single-walled carbon nanotubes (s-SWCNTs) represent a tunable model one-dimensional system with exceptional optical and electronic properties. High-throughput separation and purification strategies have enabled the integration of s-SWCNTs into a number of optoelectronic applications, including photovoltaics (PVs). In this Perspective, we discuss the fundamental underpinnings of two model PV interfaces involving s-SWCNTs. We first discuss s-SWCNT–fullerene heterojunctions where exciton dissociation at the donor–acceptor interface drives solar energy conversion. Next, we discuss charge extraction at the interface between s-SWCNTs and a photoexcited perovskite active layer. In each case, the use of highly enriched semiconducting SWCNT samples enables fundamental insights into the thermodynamic and kinetic mechanisms that drive the efficient conversion of solar photons into long-lived separated charges. These model systems help to establish design rules for next-generation PV devices containing...

Semiconducting Single-Walled Carbon Nanotubes in Solar Energy Harvesting

We have discovered that films of carbon single wall nanotubes (SWNTs) make excellent back contacts to CdTe devices without any modification to the CdTe surface. Efficiencies of SWNT-contacted devices are slightly higher than otherwise identical devices formed with standard Au/Cu back contacts. The SWNT layer is thermally stable and easily applied with a spray process, and SWNT-contacted devices show no signs of degradation during accelerated life testing.

/pdf/wiring-up-carbon-single-wall-nanotubes-to-polycrystalline-1vksoxdabh.pdf

Wiring-up carbon single wall nanotubes to polycrystalline inorganic semiconductor thin films: low-barrier, copper-free back contact to CdTe solar cells.

We have developed a laser beam induced current imaging tool for photovoltaic devices and modules that utilizes diode pumped Q-switched lasers. Power densities on the order of one sun (100 mW/cm2) can be produced in a ∼40 μm spot size by operating the lasers at low diode current and high repetition rate. Using galvanostatically controlled mirrors in an overhead configuration and high speed data acquisition, large areas can be scanned in short times. As the beam is rastered, focus is maintained on a flat plane with an electronically controlled lens that is positioned in a coordinated fashion with the movements of the mirrors. The system can also be used in a scribing mode by increasing the diode current and decreasing the repetition rate. In either mode, the instrument can accommodate samples ranging in size from laboratory scale (few cm2) to full modules (1 m2). Customized LabVIEW programs were developed to control the components and acquire, display, and manipulate the data in imaging mode.

High speed, intermediate resolution, large area laser beam induced current imaging and laser scribing system for photovoltaic devices and modules

A novel approach to fabricate CuIn(S,Se) 2 (CIS) thin films through ultrasonically spraying a hydrazine-based precursor solution onto a heated substrate is reported. The effects of the composition of the precursor solutions and the deposition temperature on the CIS film properties were investigated by comparing thin films fabricated using aqueous metal salt solution, anhydrous hydrazine solution, and hydrazine hydrate solution at various deposition temperatures. Crystallite size and texture coefficient in the preferred (112) orientation in the sprayed films increased when the aqueous solution was replaced by hydrazine-based solutions. Additionally, the hydrazine-based precursor solutions resulted in films with better surface smoothness and compositional uniformity than those fabricated using water-based solutions and the hydrazine hydrate solution resulting in the smoothest, most uniform films. The sprayed films were used to fabricate preliminary solar cells that demonstrated a modest photovoltaic response. With optimization, the synthesis of high-quality CIS films by spray pyrolysis from a hydrazine hydrate solution could demonstrate the potential for a low-cost, high-throughput manufacturing process.

Spray Pyrolysis of CuIn(S,Se) 2 Thin Films Using Hydrazine-based Solutions

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

Jonathan L. DeWitt

Author Tools

Chat about Author

Papers

Wiring-up carbon single wall nanotubes to polycrystalline inorganic semiconductor thin films: low-barrier, copper-free back contact to CdTe solar cells.

High speed, intermediate resolution, large area laser beam induced current imaging and laser scribing system for photovoltaic devices and modules

Spray Pyrolysis of CuIn(S,Se) 2 Thin Films Using Hydrazine-based Solutions