The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear $e^+e^-$ collider under development at CERN. Following the CLIC conceptual design published in 2012, this report provides an overview of the CLIC project, its current status, and future developments. It presents the CLIC physics potential and reports on design, technology, and implementation aspects of the accelerator and the detector. CLIC is foreseen to be built and operated in stages, at centre-of-mass energies of 380 GeV, 1.5 TeV and 3 TeV, respectively. CLIC uses a two-beam acceleration scheme, in which 12 GHz accelerating structures are powered via a high-current drive beam. For the first stage, an alternative with X-band klystron powering is also considered. CLIC accelerator optimisation, technical developments and system tests have resulted in an increased energy efficiency (power around 170 MW) for the 380 GeV stage, together with a reduced cost estimate at the level of 6 billion CHF. The detector concept has been refined using improved software tools. Significant progress has been made on detector technology developments for the tracking and calorimetry systems. A wide range of CLIC physics studies has been conducted, both through full detector simulations and parametric studies, together providing a broad overview of the CLIC physics potential. Each of the three energy stages adds cornerstones of the full CLIC physics programme, such as Higgs width and couplings, top-quark properties, Higgs self-coupling, direct searches, and many precision electroweak measurements. The interpretation of the combined results gives crucial and accurate insight into new physics, largely complementary to LHC and HL-LHC. The construction of the first CLIC energy stage could start by 2026. First beams would be available by 2035, marking the beginning of a broad CLIC physics programme spanning 25-30 years.

pdf/the-compact-linear-collider-clic-2018-summary-report-5d82ypkh41.pdf

The Compact Linear Collider (CLIC) - 2018 Summary Report

Preface Glossary 1. Experimental errors 1.1. Why estimate errors? 1.2. Random and systematic errors 1.3. Distributions 1.4. Mean and variance 1.5. Gaussian distribution 1.6. The meaning of s 1.7. Combining errors 1.8. Systematic errors 1.9. An example including random and systematic errors 1.10. Combining results of different experiments 1.11. Worked examples 1.12. Does it feel right? 2. Least squares fitting 2.1. What are we trying to do 2.2. Weighted sum of squares 2.3. Determining the parameters 2.4. The error on the gradient and the intercept 2.5. Other examples 2.6. Observed numbers 2.7. Parameter testing 2.8. Distribution testing 2.9. Worked example of a straight line fit 2.10. Summary of straight line fitting Problems Appendices.

A practical guide to data analysis for physical science students: Statistical tables

The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear $e^+e^-$ collider under development by international collaborations hosted by CERN. This document provides an overview of the design, technology, and implementation aspects of the CLIC accelerator. For an optimal exploitation of its physics potential, CLIC is foreseen to be built and operated in stages, at centre-of-mass energies of 380 GeV, 1.5 TeV and 3 TeV, for a site length ranging between 11 km and 50 km. CLIC uses a Two-Beam acceleration scheme, in which normal-conducting high-gradient 12 GHz accelerating structures are powered via a high-current Drive Beam. For the first stage, an alternative with X-band klystron powering is also considered. CLIC accelerator optimisation, technical developments, and system tests have resulted insignificant progress in recent years. Moreover, this has led to an increased energy efficiency and reduced power consumption of around 170 MW for the 380 GeV stage, together with a reduced cost estimate of approximately 6 billion CHF. The construction of the first CLIC energy stage could start as early as 2026 and first beams would be available by 2035, marking the beginning of a physics programme spanning 25-30 years and providing excellent sensitivity to Beyond Standard Model physics, through direct searches and via a broad set of precision measurements of Standard Model processes, particularly in the Higgs and top-quark sectors.

The Compact Linear Collider (CLIC) – Project Implementation Plan

The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear e$^+$e$^-$ collider under development by international collaborations hosted by CERN. This document provides an overview of the design, technology, and implementation aspects of the CLIC accelerator and the detector. For an optimal exploitation of its physics potential, CLIC is foreseen to be built and operated in stages, at centre-of-mass energies of 380 GeV, 1.5 TeV and 3 TeV, for a site length ranging between 11 km and 50 km. CLIC uses a two-beam acceleration scheme, in which normal-conducting high-gradient 12 GHz accelerating structures are powered via a high-current drive beam. For the first stage, an alternative with X-band klystron powering is also considered. CLIC accelerator optimisation, technical developments, and system tests have resulted in significant progress in recent years. Moreover, this has led to an increased energy efficiency and reduced power consumption of around 170 MW for the 380 GeV stage, together with a reduced cost estimate of approximately 6 billion CHF. The detector concept, which matches the physics performance requirements and the CLIC experimental conditions, has been refined using improved software tools for simulation and reconstruction. Significant progress has been made on detector technology developments for the tracking and calorimetry systems. The construction of the first CLIC energy stage could start as early as 2026 and first beams would be available by 2035, marking the beginning of a physics programme spanning 25-30 years and providing excellent sensitivity to Beyond Standard Model physics, through direct searches and via a broad set of precision measurements of Standard Model processes, particularly in the Higgs and top-quark sectors.

The Compact Linear e$^+$e$^-$ Collider (CLIC): Accelerator and Detector

The proposed Compact Linear Collider (CLIC) uses a high intensity, low energy drive beam producing the RF power to accelerate the low intensity main beam with 100 MeV/m gradient. This scheme puts stringent requirements on drive beam stability in terms of phase, energy and current. Finding and understanding the sources of jitter plays a key role in their mitigation. In this paper, we report on the recent studies in the CLIC Test Facility (CTF3). New jitter and drift sources were identified and adequate beam-based feed-backs were implemented and commissioned. Finally, we present the resulting improvement of drive beam stability.

https://cds.cern.ch/record/2207421/files/wepor007.pdf

Recent Improvements in Drive Beam Stability in CTF3

https://cds.cern.ch/record/2207420/files/wepor006.pdf

Demonstration of CLIC Level Phase Stability using a High Bandwidth, Low Latency Drive Beam Phase Feedforward System at the CLIC Test Facility CTF3

The CLIC two beam acceleration technology requires a drive beam phase stability better than 0.3 deg rms at 12 GHz, corresponding to a timing stability below 50 fs rms. For this reason the CLIC design includes a phase stabilization feed-forward system. It relies on precise beam phase measurements and their subsequent correction in a chicane with the help of fast kickers. A prototype of such a system is being installed in the CLIC Test Facility CTF3. In this paper its design and implementation is described in detail. Additionally, the performance of the precision phase monitor prototypes installed at the end of the CTF3 linac, as measured with the drive beam, is presented.

https://cds.cern.ch/record/1575566/files/CLIC-Note-1007.pdf

Design of Phase Feed Forward System in CTF3 and Performance of Fast Beam Phase Monitors

We report the results of a low-latency beam phase feed-forward system built to stabilize the arrival time of a relativistic electron beam. The system was operated at the Compact Linear Collider (CLIC) Test Facility (CTF3) at CERN where the beam arrival time was stabilized to approximately 50 fs. The system latency was 350 ns and the correction bandwidth >23 MHz. The system meets the requirements for CLIC.

Stabilization of the arrival time of a relativistic electron beam to the 50 fs level

The Compact Linear Collider (CLIC) is a proposal for a future linear electron--positron collider that could achieve collision energies of up to 3 TeV. In the CLIC concept the main high energy beam is accelerated using RF power extracted from a high intensity drive beam, achieving an accelerating gradient of 100 MV/m. This scheme places strict tolerances on the drive beam phase stability, which must be better than 0.2 degrees at 12 GHz. To achieve the required phase stability CLIC proposes a high bandwidth (G17.5 MHz), low latency drive beam "phase feedforward" (PFF) system. In this system electromagnetic kickers, powered by 500 kW amplifiers, are installed in a chicane and used to correct the phase by deflecting the beam on to longer or shorter trajectories. A prototype PFF system has been installed at the CLIC Test Facility, CTF3; the design, operation and commissioning of which is the focus of this work. Two kickers have been installed in the pre-existing chicane in the TL2 transfer line at CTF3 for the prototype. New optics have been created for the line to take these changes in to account, incorporating new constraints to obtain the desired phase shifting behaviour. Three new phase monitors have also been installed, one for the PFF input and two to verify the system performance. The resolution of these monitors must be significantly better than 0.2 degrees to achieve CLIC-level phase stability. A point by point resolution as low as 0.13 degrees has been achieved after a series of measurements and improvements to the phase monitor electronics. The performance of the PFF system depends on the correlation between the beam phase as measured at the input to the PFF system, and the downstream phase, measured after the correction chicane. Preliminary measurements found only 40% correlation. The source of the low correlation was determined to be energy dependent phase jitter, which has been mitigated after extensive efforts to measure, model and adjust the machine optics. A final correlation of 93% was achieved, improving the theoretical reduction in jitter using the PFF system from a factor 1.1 to a factor 2.7. The performance and commissioning of the kicker amplifiers and PFF controller are also discussed. Beam based measurements are used to determine the optimal correction timing. With a maximum output of around 650 V the amplifiers provide a correction range of ±5.5 ± 0.3 degrees. Finally, results from operation of the complete system are presented. A mean phase jitter of 0.28 ± 0.02 degrees is achieved, in agreement with the theoretical prediction of 0.27 ± 0.02 degrees for an optimal system with the given beam conditions. The current limitations of the PFF system, and possible future improvements to the setup, are also discussed.

Development of a Beam-based Phase Feedforward Demonstration at the CLIC Test Facility (CTF3)

In the CLIC two beam acceleration concept the phase synchronisation between the main beam and the RF power extracted from the drive beam must be maintained to within 0.2 degrees of 12 GHz [1, 2]. A drive beam phase feedforward system with bandwidth above 17.5 MHz is required to reduce the drive beam phase jitter to this level [3]. The system will correct the drive beam phase by varying the path length through a chicane via the use of fast strip line kickers. A prototype of the system is in the final stages of installation at the CLIC test facility CTF3 at CERN. This paper presents results from preparations for the phase feedforward system relating to optics improvements, the development of a slow phase feedback that will be run in parallel with the feedforward system and first tests of the kicker amplifier and kickers.

Design, Hardware Tests and First Results From the CLIC Drive Beam Phase Feed-Forward Prototype at CTF3

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

Jack Roberts

Author Tools

Chat about Author