Plasma-surface interaction in the Be/W environment: Conclusions drawn from the JET-ILW for ITER

The key remaining physics design issue for the ITER tungsten (W) divertor is the question of monoblock (MB) front surface shaping in the high heat flux target areas of the actively cooled targets. Engineering tolerance specifications impose a challenging maximum radial step between toroidally adjacent MBs of 0.3 mm. Assuming optical projection of the parallel heat loads, magnetic shadowing of these edges is required if quasi-steady state melting is to be avoided under certain conditions during burning plasma operation and transiently during edge localized mode (ELM) or disruption induced power loading. An experiment on JET in 2013 designed to investigate the consequences of transient W edge melting on ITER, found significant deficits in the edge power loads expected on the basis of simple geometric arguments, throwing doubt on the understanding of edge loading at glancing field line angles. As a result, a coordinated multi-experiment and simulation effort was initiated via the International Tokamak Physics Activity (ITPA) and through ITER contracts, aimed at improving the physics basis supporting a MB shaping decision from the point of view both of edge power loading and melt dynamics. This paper reports on the outcome of this activity, concluding first that the geometrical approximation for leading edge power loading on radially misaligned poloidal leading edges is indeed valid. On this basis, the behaviour of shaped and unshaped monoblock surfaces under stationary and transient loads, with and without melting, is compared in order to examine the consequences of melting, or power overload in context of the benefit, or not, of shaping. The paper concludes that MB top surface shaping is recommended to shadow poloidal gap edges in the high heat flux areas of the ITER divertor targets.

https://publikationen.bibliothek.kit.edu/1000076499/4840600

Physics conclusions in support of ITER W divertor monoblock shaping

The JET ITER-Like Wall experiment (JET-ILW) provides an ideal test bed to investigate plasma-surface interaction (PSI) and plasma operation with the ITER plasma-facing material selection employing beryllium in the main chamber and tungsten in the divertor. The main PSI processes: material erosion and migration, (b) fuel recycling and retention, (c) impurity concentration and radiation have be1en studied and compared between JET-C and JET-ILW. The current physics understanding of these key processes in the JET-ILW revealed that both interpretation of previously obtained carbon results (JET-C) and predictions to ITER need to be revisited. The impact of the first-wall material on the plasma was underestimated. Main observations are: (a) low primary erosion source in H-mode plasmas and reduction of the material migration from the main chamber to the divertor ( factor 7 ) as well as within the divertor from plasma-facing to remote areas ( factor 30 - 50 ). The energetic threshold for beryllium sputtering minimises the primary erosion source and inhibits multi-step re-erosion in the divertor. The physical sputtering yield of tungsten is low as 10 - 5 and determined by beryllium ions. (b) Reduction of the long-term fuel retention ( factor 10 - 20 ) in JET-ILW with respect to JET-C. The remaining retention is caused by implantation and co-deposition with beryllium and residual impurities. Outgassing has gained importance and impacts on the recycling properties of beryllium and tungsten. (c) The low effective plasma charge ( Z eff = 1.2 ) and low radiation capability of beryllium reveal the bare deuterium plasma physics. Moderate nitrogen seeding, reaching Z eff = 1.6 , restores in particular the confinement and the L-H threshold behaviour. ITER-compatible divertor conditions with stable semi-detachment were obtained owing to a higher density limit with ILW. Overall JET demonstrated successful plasma operation in the Be/W material combination and confirms its advantageous PSI behaviour and gives strong support to the ITER material selection.

Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.

http://iopscience.iop.org/article/10.1088/0029-5515/53/10/104002/pdf

Overview of the JET results with the ITER-like wall

Erosion and deposition were studied in the JET divertor during the first JET ITER-like wall campaign 2011 to 2012 using marker tiles. An almost complete poloidal section consisting of tiles 0, 1, 3 ...

/pdf/erosion-and-deposition-in-the-jet-divertor-during-the-first-36tbg8pkd1.pdf

Erosion and deposition in the JET divertor during the first ILW campaign

Parallel heat flux calculations at the JET divertor have been based on the assumption that all incoming heat is due to the projection of the heat flux parallel to the magnetic line, q, plus a const ...

https://iopscience.iop.org/article/10.1088/1741-4326/aad83e/pdf

An improved model for the accurate calculation of parallel heat fluxes at the JET bulk tungsten outer divertor

Tungsten (W) melting is a major concern for next step fusion devices. Two ELM induced tungsten melting experiments have been performed in JET by introducing two special target plate lamellae design ...

/pdf/thermal-analysis-of-protruding-surfaces-in-the-jet-divertor-1pzepv3267.pdf

Thermal analysis of protruding surfaces in the JET divertor

This paper covers aspects of long-term evolution of intrinsic impurities in the JET tokamak with respect to the newly installed ITER-like wall (ILW). At first the changes related to the change over from the JET-C to the JET-ILW with beryllium (Be) as the main wall material and tungsten (W) in the divertor are discussed. The evolution of impurity fluxes in the newly installed W divertor with respect to studying material migration is described. In addition, a statistical analysis of transient impurity events causing significant plasma contamination and radiation losses is shown. The main findings comprise a drop in carbon content (×20) (see also Brezinsek et al (2013 J. Nucl. Mater. 438 S303)), low oxygen content (×10) due to the Be first wall (Douai et al 2013 J. Nucl. Mater. 438 S1172–6) as well as the evolution of the material mix in the divertor. Initially, a short period of repetitive ohmic plasmas was carried out to study material migration (Krieger et al 2013 J. Nucl. Mater. 438 S262). After the initial 1600 plasma seconds the material surface composition is, however, still evolving. With operational time, the levels of recycled C are increasing slightly by 20% while the Be levels in the deposition-dominated inner divertor are dropping, hinting at changes in the surface layer material mix made of Be, C and W. A steady number of transient impurity events, consisting of W and constituents of inconel, is observed despite the increase in variation in machine operation and changes in magnetic configuration as well as the auxiliary power increase.

https://iopscience.iop.org/article/10.1088/0029-5515/53/7/073043/pdf

Long-term evolution of the impurity composition and impurity events with the ITER-like wall at JET

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

I. Coffey

Author Tools

Chat about Author

Papers

An improved model for the accurate calculation of parallel heat fluxes at the JET bulk tungsten outer divertor

Thermal analysis of protruding surfaces in the JET divertor

Long-term evolution of the impurity composition and impurity events with the ITER-like wall at JET