다중혈관 관상동맥 환자에서 y-문합을 이용하여 양쪽 내흉동맥만을 사용한 우회술의 조기 성적

To design reliable high voltage cables, clean materials with superior insulating properties capable of operating at high electric field levels at elevated temperatures are required. This study aims at the electrical characterization of a byproduct-free crosslinked copolymer blend, which is seen as a promising alternative to conventional peroxide crosslinked polyethylene currently used for high voltage direct current cable insulation. The characterization entails direct current (DC) conductivity, dielectric response and surface potential decay measurements at different temperatures and electric field levels. In order to quantify the insulating performance of the new material, the electrical properties of the copolymer blend are compared with those of two reference materials; i.e., low-density polyethylene (LDPE) and peroxide crosslinked polyethylene (XLPE). It is found that, for electric fields of 10–50 kV/mm and temperatures varying from 30 °C to 70 °C, the DC conductivity of the copolymer blend is in the range of 10−17–10−13 S/m, which is close to the conductivity of crosslinked polyethylene. Furthermore, the loss tangent of the copolymer blend is about three to four times lower than that of crosslinked polyethylene and its magnitude is on the level of 0.01 at 50 °C and 0.12 at 70 °C (measured at 0.1 mHz and 6.66 kV/mm). The apparent conductivity and trap density distributions deduced from surface potential decay measurements also confirmed that the new material has electrical properties at least as good as currently used insulation materials based on XLPE (not byproduct-free). Thus, the proposed byproduct-free crosslinked copolymer blend has a high potential as a prospective insulation medium for extruded high voltage DC cables.

/pdf/electrical-characterization-of-a-new-crosslinked-copolymer-r3igmodhte.pdf

Electrical Characterization of a New Crosslinked Copolymer Blend for DC Cable Insulation

This paper focuses on the multi-dimensional performance analysis including the oxidation performance, crystal morphology, thermal properties, mechanical properties and dielectric behavior of the thermally aged extra high voltage XLPE submarine cable insulation. Results show that the antioxidation and thermal oxidative aging of XLPE insulation are coexisting and competing during the thermal degradation process. In the early stage of thermal degradation, the antioxidation of XLPE insulation is dominant resulting in the decline of the spacing between spherulites. In the later stage of thermal degradation, thermally oxidative aging of XLPE insulation is dominant, which leads to the damage of the crystalline morphology and the rapid generation of aging products. It is indicated that the mechanical strength of the XLPE insulation is mainly determined by its internal crystalline morphology, while the dielectric properties of the XLPE insulation are governed by the crystalline morphology, aging products and micro interface. With the thermal aging time extended, the breakdown strength of XLPE insulation first increases and then decreases, which is determined by its amorphous region and aging products.

Multi-dimensional Analysis and Correlation Mechanism of Thermal Degradation Characteristics of XLPE Insulation for Extra High Voltage Submarine Cable

This paper presents an estimate for the influence of service time on the conduction current characteristics of a 10 kV AC XLPE. The experimental conduction current results show that the space charge accumulation threshold increases with service time. Fourier transform infrared (FT-IR) and differential scanning calorimetry (DSC) experiments show increased thermo-oxidative aging and reduced crystallinity as the service time increases. This results in deeper traps in the XLPE material which can be verified from isothermal surface potential decay experiments. Based on the experimental results, the numerical analysis of thermo-electric fields is carried out for 10 kV AC XLPE cables with different service times under bipolar DC operation mode. It shows that the DC power for 10 kV AC XLPE cable in bipolar DC operation is higher than the AC power, whereas the DC operating voltage and DC power increases with the service time. In order to ensure a safe and long service life of the cables in DC operation, a conductor temperature of 60 °C and DC operating voltage of 11 kV are recommended for 10 kV AC XLPE cables in bipolar DC operation.

Numerical analysis of thermo-electric field for AC XLPE cables with different service times in DC operation based on conduction current measurement

Effect of degassing treatment durations on physico-chemical and electrical properties of 500 kV extra HVDC XLPE cable insulation

This paper reports the effect of thermal ageing on the space charge characteristics, DC conductivities and trap energy distributions of 320 kV HVDC XLPE. Specimens were prepared by a heating press method in the laboratory. The specimens were placed in a thermal oven and thermally aged at 130 °C up to 30 days. Space charges were measured by a pulsed electro-acoustic setup. The results showed that the reference samples had limited hetero charge accumulations near both electrodes in the samples. The homo-charge accumulation was appeared with an increase of the aged time. The space charge accumulation in the samples was transferred from hetero-charge accumulation to homo-charge accumulation with an increase of the ageing time. The electric field distribution in the sample gradually increased with the appearance of the homo-charge accumulation, whereas the homo charges evidently distorted the electric field in the samples with the increasing ageing time. The DC conductivities of the aged samples consistently increased with the increase of the measured electric field. The obtained results of apparent mobility of the charge carriers, the activation energy and the trap energy density illustrated that thermal ageing could facilitate the homo-charge accumulation in the sample. The dominant effect of thermal ageing on the sample was elucidated by using various analytical techniques. It was found that the thermal ageing would affect the material properties and facilitate the increase of the trap energy density and the space charge accumulations in the samples.

Effect of thermal ageing on charge dynamics and material properties of 320 kV HVDC XLPE

With rapid development of renewable energies and dc loads in distribution grids, converting ac distribution grids into dc operation has become a promising method to utmost utilize the present ac distribution grid in large cities. This paper reports a numerical investigation of thermo-electric fields of a three-core 10-kV ac cross-linked polyethylene (XLPE) cable and cable joint in the dc operation. DC conduction current for the XLPE and silicon rubber (SiR) was evaluated at different temperatures and electric fields. The thermo-electric field simulation was performed by COMSOL Multiphysics according to the measured data. The obtained result showed that the threshold of XLPE at 65 °C is 3.1 MV/m, whereas the threshold of SiR at 60 °C is 2.2 MV/m. It was found that the maximum electric field of the cable operated in dc voltage up to 12.5 kV was below the threshold of 3.1 MV/m. The maximum electric field in the cable joint appeared at the high voltage screen tube, whereas the maximum electric field at the high voltage screen tube was less than the threshold of SiR at a temperature difference of 25 °C. Moreover, the maximum transmission power of the three-core 10-kV AC XLPE cables running at the ±10-kV bipolar dc operation was 1.36 times of the power in the ac operation. It was elucidated that the three-core ac 10-kV XLPE cable could be operated reliably at ±10 kV in bipolar dc topology with sufficient safety margin. It is beneficial to upgrade the ac distribution grid to the dc distribution grid.

/pdf/numerical-analysis-of-thermo-electric-field-for-ac-xlpe-5fwem9b6ad.pdf

Numerical Analysis of Thermo-Electric Field for AC XLPE Cable in DC Operation Based on Conduction Current Measurement

In this paper, a thermo-electric field coupling model was established to perform simulations on a typical three-core AC 10 kV XLPE cable in bipolar DC operation by the finite element analysis software ANSYS. The obtained results showed that when the conductor temperature of the cable was 70 oC and the cable was laid in the environmental temperature of 40 °C, the estimated cable ampacity could reach up to 440 A. The maximum of electric field in the cable insulation was settled below 3 kV/mm to minimize the effect of space charge for the cable in DC operation. It was found that the cable could run at the bipolar DC ± 10 kV with enough safety margin. Moreover, the maximum transmission power of the cable running at the bipolar DC ± 10 kV mode was 1.37 times of the power in the AC operation. It is promising for upgrading the present AC grid into future DC grid.

Numerical analysis of thermo-electric field for 10 kV AC XLPE cable in DC operation

This paper presents investigations on a usage of graphene as a voltage stabilizer for polyethylene blends in the potential recyclable high voltage direct current (HVDC) cable insulation. Thermal and electrical properties of the blends with/without graphene were evaluated by thermo-gravimetric analysis (TGA), differential scanning calorimetry (DSC), electrical treeing tests, DC conductivity and space charge measurements. Trap energy distributions in the blends were estimated using the measured space charge decay data. The obtained results show that additive-like amounts of graphene can improve the thermal stability of the polyethylene blends. The influence of the graphene on the tree inception voltage (TIV) of the polyethylene blends is not significant, whereas the low density polyethylene/high density polyethylene (LDPE/HDPE) with/without graphene demonstrates the highest TIV comparing to the LDPE, LDPE/polypropylene, and their corresponding graphene added materials. It is found that the DC conductivity of the polyethylene blends with/without graphene increases consistently with the increase of the temperature. The conductivity of the LDPE/HDPE decreases apparently with the inclusion of graphene. It has been shown that space charge accumulations can be suppressed by the addition of graphene in the polyethylene blends. It is postulated that the high trap level and trap energy density of the polyethylene blends with graphene are closely connected to the suppression of the space charge accumulation in the blends.

Polyethylene blends with/without graphene for potential recyclable HVDC cable insulation

This paper reports a new application of graphene as voltage stabilizer for polyethylene blends of the future environmental-friendly cable insulation materials. Electrical treeing in needle-plane electrode test objects of low-density polyethylene (LDPE) and its high-density polyethylene (HDPE), polypropylene (PP) blends with/without graphene were recorded by a real-time microscope observation system and a synchronized partial discharge (PD) detection system. The obtained results showed that the electrical tree initiation time of the LDPE decreased continually with the addition of 10 wt% HDPE and PP, respectively. It has been shown that the addition of 0.2 wt% graphene improves resistance of the tree inception of the LDPE and its blends. The LDPE/HDPE blended specimen with filled graphene had the longest tree initiation time (TIT) within all the tested samples, which was one time of the TIT of pure LDPE objects, and over 150% extension of the TIT of the unfilled LDPE/HDPE samples. It was also found that the graphene filled LDPE blends usually showed higher discharge magnitude than the pure LDPE material. It was postulated that the addition of grapheme would facilitate the PD in the tree channels of the samples with voltage stabilizer, but the influence of graphene voltage stabilizer on the microstructure and morphology of the blends could also enhance the tree inception resistance in the materials.

Electrical treeing of polyethylene blends with/without voltage stabilizer

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

Hao Zhou

Author Tools

Chat about Author