The use of a LCL-filter mitigates the switching ripple injected in the grid by a three-phase active rectifier. However stability problems could arise in the current control loop. In order to overcome them a damping resistor can be inserted, at the price of a reduction of the efficiency. On the contrary the use of the active damping seems really attractive but it is often limited by the use of more sensors respect to the standard control and by the complex tuning procedure. This paper introduces a new active damping method that does not need the use of more sensors and that can be tuned using genetic algorithms. It consists of adding a filter on the reference voltage for the converter's modulator. The tuning process of this filter is easily done, for a wide range of sampling frequencies, with the use of genetic algorithms. This method is used only for the optimum choice of the parameters of the filter and an on-line implementation is not needed. Thus the resulting active damping solution does not need new sensors or complex calculations. Moreover, in the paper particular attention is devoted to the dynamics of the system due to the introduction of the active damping.

Genetic algorithm based design of the active damping for a LCL-filter three-phase active rectifier

Active rectifiers/inverters are becoming used more and more often in regenerative systems and distributed power systems. Typically, the interface between the grid and rectifier is either an inductor or an LCL-filter. The use of an LCL-filter mitigates the switching ripple injected in the grid by a three-phase active rectifier. However, stability problems can arise in the current control loop. In order to overcome them, a damping resistor can be inserted, at the price of a reduction of efficiency. The use of active damping by means of control may seem attractive but it is often limited by the use of more sensors compared to the standard control and also by a complex tuning procedure of the controllers. This paper introduces a new active damping method that does not require the use of more sensors. It consists of adding a filter on the reference voltage for the modulator. The tuning process of this filter is easily done, for a wide range of sampling frequencies, with the use of genetic algorithms. This method is used only for the optimum choice of the parameters in the filter and an on-line implementation is not needed. Thus the resulting active damping solution does not need new sensors or complex calculations. Moreover, in the paper particular attention is devoted to the susceptibility of the system in a high polluting environment.

Genetic algorithm-based design of the active damping for an LCL-filter three-phase active rectifier

This paper provides a comprehensive guideline for the design of a single-phase PFC targeting for minimal volume, as it is highly relevant for ultracompact integrated systems. It is shown, how different operation modes (continuous, boundary, and discontinuous conduction mode) may influence the design and consequently the achieved power density. Furthermore, the effect of interleaving of several boost stages is analyzed as a measure for compactness increase. Finally, the selection of the appropriate switching frequency in order to achieve an overall optimized system is discussed. In this way, the design of the crucial components is carried out, namely, the boost inductor, including a volume optimization through a thermal connection to the heat sink; the output capacitor considering the rms current stress; and the input filter, which is designed for compliance with high-frequency electromagnetic compatibility standards, taking into account the quasi-peak detection measurement of the test receiver equipment.

Design Guidelines for Interleaved Single-Phase Boost PFC Circuits

This paper presents a systematic evaluation approach of three-phase pulsewidth-modulated (PWM) AC-AC converter topologies for high-density applications. All major components and subsystems in a converter are considered and the interdependence of all the constraints and design parameters is systematically studied. The key design parameters, including switching frequency, modulation scheme, and passive values, are selected by considering their impacts on loss, harmonics, electromagnetic interference (EMI), control dynamics and stability, and protection. The component selection criteria as well as the physical design procedures are developed from the high-density standpoint. The concept of using the same inductor for harmonic suppression and EMI filtering is introduced in the design. With the proposed methodology, four converter topologies, a back-to-back voltage source converter (BTB-VSC), a nonregenerative three-level boost (Vienna-type) rectifier plus voltage source inverter (NTR-VSI), a back-to-back current source converter (BTB-CSC), and a 12-switch matrix converter, are analyzed and compared for high specific power using SiC devices. The evaluation results show that with the conditions specified in this paper, BTB-VSC and NTR-VSI have considerably lower loss, resulting in higher specific power than BTB-CSC and the matrix converter. The proposed methodology can be applied to other topologies with different comparison metrics and can be a useful tool for high-density topology selection.

A Systematic Topology Evaluation Methodology for High-Density Three-Phase PWM AC-AC Converters

The design of electromagnetic interference (EMI) input filters, needed for switched power converters to fulfill the regulatory standards, is typically associated with high development effort. This paper presents a guideline for a simplified differential-mode (DM) filter design. First, a procedure to estimate the required filter attenuation based on the total input rms current using only a few equations is given. Second, a volume optimization of the needed DM filter based on the previously calculated filter attenuation and volumetric component parameters is introduced. It is shown that a minimal volume can be found for a certain optimal number of filter stages. The considerations are exemplified for two single-phase power factor correction converters operated in continuous and discontinuous conduction modes, respectively. Finally, EMI measurements done with a 300-W power converter prototype prove the proposed filter design method.

Guideline for a Simplified Differential-Mode EMI Filter Design

This article present GA-based design approach to optimization of power electronics circuits is shown to be a very effective and powerful tool for obtaining improved solutions compared to traditional design procedures. In the GA procedure, each design is represented using a "gene string" for the converter design problem, each gene string is used to represent the set of electrical components that define one possible converter design. The design of power electronics systems involves a large number of design variables and the application of knowledge from several different engineering fields.

Power converter design optimization

This paper presents an approach to discrete de­sign optimization of a complete power electronics converter with the objective to minimize the total component cost. The design constraints are the converter specifications, such as operating power and voltage ranges, EMI standards, size, and lifetime, as well as the component safe operating areas. The design variables are the switching frequency and the selection of the actual, commercially available components and materi­als. The genetic algorithm provides for a systematic and effi­cient search of the databases of preferred components, which contain all (datasheet-based) component parameters that are necessary for evaluating the constraints and the objective function. 
The methodology is illustrated with a developed software tool for designing a low-cost boost power factor correction (PFC) front-end converter with an input EMI filter. Compu­tationally fast and experimentally validated algebraic models of the system and its components, which include second order effects, are considered. A graphical user interface for manag­ing the design specifications and the component databases, controlling and monitoring the optimization process, and ana­lyzing the performance of the best designs is described. The results of a design for a 1.15 kW unit are presented.

/pdf/design-optimization-of-power-electronics-circuits-using-47c9es6j9j.pdf

Design Optimization of Power Electronics Circuits using Genetic Algorithms-A Boost PFC Converter Example

This paper presents a software tool for designing a low-cost boost power factor correction front-end converter with an input electromagnetic interference filter. A genetic algorithm based discrete optimizer is used to obtain the design. A detailed and experimentally validated model of the system, including second order effects, is considered. A graphical user interface for managing the design specifications and system component databases, controlling and monitoring the optimization process, and analyzing the performance of the top designs found by the optimizer is also described. The results of a design study for a 1.15 kW unit are presented to demonstrate the usefulness of the software tool.

Design optimization of a boost power factor correction converter using genetic algorithms

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

G. Soremekun

Author Tools

Chat about Author

Papers

Power converter design optimization

Design Optimization of Power Electronics Circuits using Genetic Algorithms-A Boost PFC Converter Example

Design optimization of a boost power factor correction converter using genetic algorithms