High-voltage engineering

HV composite polymeric insulators are being accepted increasingly for use in outdoor installations by the traditionally cautious electric power utilities worldwide. They currently represent -60 to 70% of newly installed HV insulators in Nortb America. The tremendous growth in the applications of non-ceramic composite insulators is due to their advantages over the traditional ceramic and glass insulators. These include light weight, higher mechanical strength to weight ratio, resistance to vandalism, better performance in the presence of heavy pollution in wet conditions, and comparable or better withstand voltage than porcelain or glass insulators. However, because polymeric insulators are relatively new, the expected lifetime and their long-term reliability are not known and therefore are of concern to users. Additionally they might suffer from erosion and tracking in the presence of severe contamination and sustained moisture. This leads to the development of dry band arcing that under certain circumstances could lead to failure of polymer insulators. In this paper a review is presented of the recent performance experience of HV composite polymeric insulators in outdoor service, testing methods, aging, the ranking of the materials, the role of fillers, the role of low molecular weight components present in the insulators, the mechanisms responsible for the loss and recovery of hydrophobicity, one of the most important properties of polymers, the mechanisms of failure, detection of faults, type and quantity of natural contaminants, effects of exposure to rain, hydrocarbons, stationary air and wind, various methods to optimize the electrical performance and a relatively new method for evaluating the performance status of polymeric insulators in the field.

Outdoor HV composite polymeric insulators

Crosslinked polydimethylsiloxane exposed to oxygen plasma studied by neutron reflectometry and other surface specific techniques

Hydrophobicity Recovery of Polydimethylsiloxane after Exposure to Corona Discharges

Water repellency, high surface resistivity, vandalism resistance, low density and good processability have made silicone rubbers based on polydimethylsiloxane (PDMS) very attractive materials in housings for outdoor insulation. Their ability to recover hydrophobicity after oxida. tion or contamination is of paramount importance and this is the topic of this review. A critical evaluation of the chemical and physical mechanisms responsible for hydrophobicity loss and recovery is presented.

Hydrophobicity changes in silicone rubbers

Under wet and contaminated conditions dry band arcing occurs on the surface of HV outdoor insulators coated with room temperature vulcanizing (RTV) silicone rubber. The thermal impact of the arcing on the surface of the RTV causes chemical changes. The gradual loss of hydrophobicity due to dry band arcing is of considerable concern because it results in a reduction of the withstand voltage and subsequent failure of the insulator and power outage. In this study the RTV coatings were subjected simultaneously to salt-fog and electrical stress. Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy and electron spectroscopy for chemical analysis (ESCA) were then employed to investigate the chemical changes. Possible chemical reactions and processes occurring under dry band arcing are suggested. The results of ATR-FTIR and ESCA indicate the formation of low molecular weight polydimethylsiloxane (PDMS), the reduction in the surface density of CH3 groups and crosslinking of the PDMS backbone chains at the surface. Chemical derivative analysis was also carried out to further elucidate the chemical changes on the surface of RTV coating. >

Chemical changes at the surface of RTV silicone rubber coatings on insulators during dry-band arcing

The results of a study on the loss and recovery of hydrophobicity of RTV (room-temperature vulcanizing) silicone-rubber insulator coatings in a salt-fog chamber are reported. The results complement those previously reported on the ability of the coatings to suppress leakage current and insulator flashover. The temporary loss of hydrophobicity caused by dry-band arcing and the subsequent recovery are studied in depth. The gradual loss of hydrophobicity as determined from the leakage current and the contact-angle measurements is shown to be related to the physical changes to the coating brought about by dry-band arcing. >

The loss and recovery of hydrophobicity of RTV silicone rubber insulator coatings

Room temperature vulcanizing (RTV) silicone rubber coatings are applied to electrical insulators to improve their subsequent insulation strength, particularly under wet conditions. Under prolonged wetting the hydrophobicity of the coating is reduced temporarily and the insulator protection is lost. After a dry period, a recovery of the hydrophobicity takes place. To investigate this phenomenon, the surface was subjected to various wetting conditions with and without electrical stress. Measurements of the contact and the sliding angles were used to determine the state of the surface. Using water, the surface free energy of the RTV was calculated from the contact angle measurements as a function of time of exposing the surface to salt-fog. The surface free energies due to London dispersion and hydrogen bonding forces on the surface of RTV coatings were calculated from the contact angle measurements using both water and methylene iodide. Good agreement was obtained with the literature value for a virgin RTV surface. The chemical changes of the surface are shown to be responsible for the loss of hydrophobicity. >

Hydrophobic behavior of insulators coated with RTV silicone rubber

The ability of room temperature vulcanizing (RTV) silicone rubber insulator coatings to suppress leakage current, thereby preventing power outages due to contamination, was studied. The RTV coatings were applied to porcelain suspension and line post insulators for a comparative study of the performance of coated and uncoated insulators. A study of the role of alumina trihydrate (ATH) which is used to impart tracking and erosion resistance to RTV coating is reported. A study of the diffusion of silicone fluid from the bulk to the surface of the RTV silicone rubber having various ATH filler levels using attenuated total reflection (ATR) Fourier transform infrared (FTIR) spectroscopy is also reported. It has been found that the diffusion rate of the silicone fluid from the bulk to the surface of the coating after extensive dry band arcing decreases with increasing filler level. >

Effects of filler level in RTV silicone rubber coatings used in HV insulators

The paper presents a review of room temperature vulcanized (RTV) silicone rubber high voltage insulator coatings (HVIC). These coatings are designed to replace greasing and waterwashing of insulators. Present day coatings are the result of nearly thirty years of development and use. In all but a very few dirty environments, these coatings have lasted ten or more years without maintenance and where maintenance has been found to be necessary, water washing is done at a significantlyreduced schedule. The paper focuses on the important characteristics of these coatings and on the rigorous attention that is required in their application in order to ensure good performance.

RTV silicone rubber coatings for outdoor insulators

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

E.A. Cherney

Author Tools

Chat about Author