[1] Satellite based fire radiant energy retrievals are widely applied to assess biomass consumed and emissions at regional to global scales. A known potential source of uncertainty in biomass burning estimates arises from fuel moisture but this impact has not been quantified in previous studies. Controlled fire laboratory experiments are used in this study to examine the biomass consumed and the radiant energy release (Fire Radiative Energy, FRE, (MJ)) for western white pine needle fuels burned with water content (WC, unitless) from 0.01 to 0.14. Results indicate a significant relationship: FRE per kilogram of fuel consumed = −5.32 WC + 3.025 (r2 = 0.83, n = 24, P < 0.001) and imply that not taking into account fuel moisture variations in the assumed relationship between FRE and fuel consumed can lead to systematic biases. A methodological framework to derive a revised formula that enables the estimation of biomass consumed from FRE, which explicitly takes into account fuel water content, is presented.

http://www.firescience.gov/projects/07-2-1-60/project/07-2-1-60_2013_Smith_FREmoisture.pdf

Quantification of fuel moisture effects on biomass consumed derived from fire radiative energy retrievals

D. Don) at 100 °C dry bulb and 70 °C wet bulb, were assessed by measuring the concentration of chemical components in the kiln atmosphere at regular time intervals and determining air-flows and temperature differentials across the stack. The volatile organic compounds (VOC) were trapped on activated carbon and analyzed by GC-MS. The aldehydes were trapped in 2,4-dinitrophenol-hydrazine solution and the aldehyde derivatives analysed by HPLC. Polar compounds were trapped in water and then alcohols were analysed by GC and organic acids by ion exchange chromatography. The two major VOC found were α-pinene and β-pinene, which made up 90% of the total discharge (405 g/m3 wood). Most of the VOC fraction was released during the early stages of drying. The release of potentially hazardous components (formaldehyde, acetaldehyde, furfural) was found to be relatively low (1.1, 8.7, and 0.1 g/m3 wood, respectively) provided the kiln emissions are well dispersed, these levels of release are unlikely to cause adverse environmental effects.

Assessment of air emissions from industrial kiln drying of Pinus radiata wood

This article reports the results of an exploratory study designed to reduce heat and electricity consumption in industrial drying of radiata pine. The experiments were performed with slight modifications of the standard drying schedules used by the sawmill to dry radiata pine in 100-m3 industrial kilns. The heat and electricity consumption were determined with data collected during the drying runs and calculations based on mathematical models. The results showed that depending on the case, heat and power consumption were respectively reduced by up to 14 and 35%.

Energy Consumption in Industrial Drying of Radiata Pine

The nature and mass flows of atmospheric emissions from an industrial kiln, drying radiata pine (Pinus radiata D.Don) timber at 140°C dry bulb and 90°C wet bulb, which was subsequently copper-chrome-arsenic (CCA) treated and redried at 90°C dry bulb and 60°C wet bulb, were assessed by measuring the concentration of chemical components in the kiln atmosphere at regular time intervals and determining air-flows and temperature differentials across the stack. The volatile organic compounds (VOCs) emitted were trapped and analyzed by GC-MS. The two major VOCs found during high temperature pre-drying and CCA re-drying were α-pinene and
β-pinene, which made up 87% and 60% of the total discharge (2433 and 145 g/m3 wood), respectively. Most of the VOC fraction was released during the early stages of drying. The polar compounds were trapped in water. Total combined amount of methanol, ethanol, acetic acid and formic acid released over the two runs were 283, 281, 117, and 260 g/m3 wood, respectively. The aldehydes were trapped in 2,4-dinitrophenyl-hydrazine solution and the aldehyde derivatives analysed by HPLC. The total release of formaldehyde and acetaldehyde during the high temperature pre-drying run were 13 and 15 g/m3
wood and the CCA re-drying run were 14 and 4 g/m3
wood, respectively.

Air emission from timber drying: high temperature drying and re-drying of CCA treated timber

Inadequate integration and/or inappropriate operating parameters of heat pump dryers may lead to troubles as too high/low discharge/suction pressures, low dehumidification efficiency and even mechanical damage to the compressor. This paper will help fix a number of common design errors and/or omissions, and suggests original control methods to avoid undesirable operational incidents and improve overall energy performance of high-temperature drying heat pumps. The scope is to provide normal and safe operating conditions, and thus accelerate the implementation of industrial drying heat pumps.

/pdf/improvements-of-high-temperature-drying-heat-pumps-4m7f3tw9yc.pdf

Improvements of high-temperature drying heat pumps

/pdf/tb73-estimating-heat-consumption-in-kiln-drying-lumber-1g6mufeoad.pdf

TB73: Estimating Heat Consumption in Kiln Drying Lumber

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

Craig E. Shuler

Author Tools

Chat about Author

Papers

TB73: Estimating Heat Consumption in Kiln Drying Lumber