This paper presents a review of the experimental achievements related to the development of high-power gyrotron oscillators for long-pulse or CW operation and pulsed gyrotrons for many applications. In addition, this work gives a short overview on the present development status of frequency step-tunable and multi-frequency gyrotrons, coaxial-cavity multi-megawatt gyrotrons, gyrotrons for technological and spectroscopy applications, relativistic gyrotrons, large orbit gyrotrons (LOGs), quasi-optical gyrotrons, fast- and slow-wave cyclotron autoresonance masers (CARMs), gyroklystrons, gyro-TWT amplifiers, gyrotwystron amplifiers, gyro-BWOs, gyro-harmonic converters, gyro-peniotrons, magnicons, free electron masers (FEMs), and dielectric vacuum windows for such high-power mm-wave sources. Gyrotron oscillators (gyromonotrons) are mainly used as high-power millimeter wave sources for electron cyclotron resonance heating (ECRH), electron cyclotron current drive (ECCD), stability control, and diagnostics of magnetically confined plasmas for clean generation of energy by controlled thermonuclear fusion. The maximum pulse length of commercially available 140 GHz, megawatt-class gyrotrons employing synthetic diamond output windows is 30 min (CPI and European KIT-SPC-THALES collaboration). The world record parameters of the European tube are as follows: 0.92 MW output power at 30-min pulse duration, 97.5% Gaussian mode purity, and 44% efficiency, employing a single-stage depressed collector (SDC) for energy recovery. A maximum output power of 1.5 MW in 4.0-s pulses at 45% efficiency was generated with the QST-TOSHIBA (now CANON) 110-GHz gyrotron. The Japan 170-GHz ITER gyrotron achieved 1 MW, 800 s at 55% efficiency and holds the energy world record of 2.88 GJ (0.8 MW, 60 min) and the efficiency record of 57% for tubes with an output power of more than 0.5 MW. The Russian 170-GHz ITER gyrotron obtained 0.99 (1.2) MW with a pulse duration of 1000 (100) s and 53% efficiency. The prototype tube of the European 2-MW, 170-GHz coaxial-cavity gyrotron achieved in short pulses the record power of 2.2 MW at 48% efficiency and 96% Gaussian mode purity. Gyrotrons with pulsed magnet for various short-pulse applications deliver Pout = 210 kW with τ = 20 μs at frequencies up to 670 GHz (η ≅ 20%), Pout = 5.3 kW at 1 THz (η = 6.1%), and Pout = 0.5 kW at 1.3 THz (η = 0.6%). Gyrotron oscillators have also been successfully used in materials processing. Such technological applications require tubes with the following parameters: f > 24 GHz, Pout = 4–50 kW, CW, η > 30%. The CW powers produced by gyroklystrons and FEMs are 10 kW (94 GHz) and 36 W (15 GHz), respectively. The IR FEL at the Thomas Jefferson National Accelerator Facility in the USA obtained a record average power of 14.2 kW at a wavelength of 1.6 μm. The THz FEL (NOVEL) at the Budker Institute of Nuclear Physics in Russia achieved a maximum average power of 0.5 kW at wavelengths 50–240 μm (6.00–1.25 THz).

/pdf/state-of-the-art-of-high-power-gyro-devices-and-free-5avfirj4z9.pdf

State-of-the-Art of High-Power Gyro-Devices and Free Electron Masers

Gyrotrons form a specific group of devices in the class of fast-wave vacuum electronic sources of coherent electromagnetic wave radiation known as electron cyclotron masers (ECMs) or cyclotron resonance masers (CRMs). The operation of CRMs is based on the cyclotron maser instability which originates from the relativistic dependence of the electron cyclotron frequency on the electron energy. This relativistic effect can be pronounced even at low voltages when the electron kinetic energy is small in comparison with the rest energy. The free energy for generation of electromagnetic (EM) waves is the energy of electron gyration in an external magnetic field. As in any fast-wave device, the EM field in a gyrotron interaction space is not localized near a circuit wall (like in slow-wave devices), but can occupy large volumes. Due to possibilities of using various methods of mode selection (electrodynamical and electronic ones), gyrotrons can operate in very high order modes. Since the use of large, oversized cavities and waveguides reduces the role of ohmic wall losses and breakdown limitations, gyrotrons are capable of producing very high power radiation at millimeter and submillimeter wavelengths. The present review is restricted primarily by the description of the development and the present state-of-the-art of gyrotrons for controlled thermonuclear fusion plasma applications. The first gyrotron was invented, designed and tested in Gorky, USSR (now Nizhny Novgorod, Russia), in 1964.

The Gyrotron at 50: Historical Overview

This paper presents a review of the experimental achievements related to the development of high-power gyrotron oscillators for long-pulse or CW operation and pulsed gyrotrons for many applications. In addition, this work gives a short overview on the present development status of frequency step-tunable and multi-frequency gyrotrons, coaxial-cavity multi-megawatt gyrotrons, gyrotrons for technological and spectroscopy applications, relativistic gyrotrons, large orbit gyrotrons (LOGs), quasi-optical gyrotrons, fast- and slow-wave cyclotron autoresonance masers (CARMs), gyroklystrons, gyro-TWT amplifiers, gyrotwystron amplifiers, gyro-BWOs, gyro-harmonic converters, gyro-peniotrons, magnicons, free electron masers (FEMs), and dielectric vacuum windows for such high-power mm-wave sources. Gyrotron oscillators (gyromonotrons) are mainly used as high-power millimeter wave sources for electron cyclotron resonance heating (ECRH), electron cyclotron current drive (ECCD), stability control, and diagnostics of magnetically confined plasmas for clean generation of energy by controlled thermonuclear fusion. The maximum pulse length of commercially available 140 GHz, megawatt-class gyrotrons employing synthetic diamond output windows is 30 min (CPI and European KIT-SPC-THALES collaboration). The world record parameters of the European tube are as follows: 0.92 MW output power at 30-min pulse duration, 97.5% Gaussian mode purity, and 44% efficiency, employing a single-stage depressed collector (SDC) for energy recovery. A maximum output power of 1.5 MW in 4.0-s pulses at 45% efficiency was generated with the QST-TOSHIBA (now CANON) 110-GHz gyrotron. The Japan 170-GHz ITER gyrotron achieved 1 MW, 800 s at 55% efficiency and holds the energy world record of 2.88 GJ (0.8 MW, 60 min) and the efficiency record of 57% for tubes with an output power of more than 0.5 MW. The Russian 170-GHz ITER gyrotron obtained 0.99 (1.2) MW with a pulse duration of 1000 (100) s and 53% efficiency. The prototype tube of the European 2-MW, 170-GHz coaxial-cavity gyrotron achieved in short pulses the record power of 2.2 MW at 48% efficiency and 96% Gaussian mode purity. Gyrotrons with pulsed magnet for various short-pulse applications deliver P out  = 210 kW with τ  = 20 μs at frequencies up to 670 GHz ( η  ≅ 20%), P out  = 5.3 kW at 1 THz ( η  = 6.1%), and P out  = 0.5 kW at 1.3 THz ( η  = 0.6%). Gyrotron oscillators have also been successfully used in materials processing. Such technological applications require tubes with the following parameters: f   >  24 GHz, P out  = 4–50 kW, CW, η   >  30%. The CW powers produced by gyroklystrons and FEMs are 10 kW (94 GHz) and 36 W (15 GHz), respectively. The IR FEL at the Thomas Jefferson National Accelerator Facility in the USA obtained a record average power of 14.2 kW at a wavelength of 1.6 μm. The THz FEL (NOVEL) at the Budker Institute of Nuclear Physics in Russia achieved a maximum average power of 0.5 kW at wavelengths 50–240 μm (6.00–1.25 THz).

/pdf/state-of-the-art-of-high-power-gyro-devices-and-free-3dd9d7und5.pdf

State-of-the-art of high power gyro-devices and free electron masers update 1995

The Wendelstein 7X (W7-X) stellarator (R = 5.5 m, a = 0.55 m, B < 3.0 T), which at present is being built at Max-Planck-Institut fur Plasmaphysik, Greifswald, aims at demonstrating the inherent ste...

/pdf/electron-cyclotron-heating-for-w7-x-physics-and-technology-2pobx2z7e6.pdf

Electron Cyclotron Heating for W7-X: Physics and Technology

In many tokamak and stellarator experiments around the globe that are investigating energy production via controlled thermonuclear fusion, electron cyclotron heating and current drive (ECH&CD) are used for plasma start-up, heating, non-inductive current drive and MHD stability control. ECH will be the first auxiliary heating method used on ITER. Megawatt-class, continuous wave (CW) gyrotrons are employed as high-power millimeter (mm)-wave sources. The present review reports on the worldwide state-of-the-art of high-power gyrotrons. Their successful development during the past years changed ECH from a minor to a major heating method. After a general introduction of the various functions of ECH&CD in fusion physics, especially for ITER, Section 2 will explain the fast-wave gyrotron interaction principle. Section 3 discusses innovations on the components of modern long-pulse fusion gyrotrons (magnetron injection electron gun (MIG), beam tunnel, cavity, quasi-optical output coupler, synthetic diamond output window, single-stage depressed collector) and auxiliary components (superconducting magnets, gyrotron diagnostics, high-power calorimetric dummy loads). Section 4 deals with present megawatt-class gyrotrons for ITER, W7-X, LHD, EAST, KSTAR and JT-60SA, and also includes tubes for moderate pulse length machines as, ASDEX-U, DIII-D, HL-2A, TCV, QUEST and GAMMA-10. In Section 5 the development of future advanced fusion gyrotrons is discussed. These are tubes with higher frequencies for DEMO, multi-frequency (multi-purpose) gyrotrons, stepwise frequency tunable tubes for plasma stabilization, injection-locked and coaxial-cavity multi-megawatt gyrotrons, as well as sub-THz gyrotrons for collective Thomson scattering (CTS). Efficiency enhancement via multi-stage depressed collectors, fast oscillation recovery methods and reliability, availability, maintainability and inspectability (RAMI) will be discussed at the end of this section.

/pdf/high-power-gyrotrons-for-electron-cyclotron-heating-and-4i6ctmqvpg.pdf

High-power gyrotrons for electron cyclotron heating and current drive

The development of high-power gyrotrons (118 GHz, 140 GHz) in continuous-wave (CW) operation for heating nuclear fusion plasmas has been in progress for several years in a joint collaboration between different European research institutes and industrial partners. The 140-GHz gyrotron being under development for the installation at the W7-X stellarator now under construction at the IPP Greifswald, Germany, operates in the TE/sub 28,8/ mode and is equipped with a diode type magnetron injection electron gun, an improved beam tunnel, a high mode-purity low-Ohmic loss cavity, an optimized nonlinear up-taper, a highly efficient internal quasi-optical mode converter, a single-stage depressed collector and an edge-cooled, single disk CVD-diamond window. RF measurements at pulse duration of a few milliseconds yielded an RF output power of 1.15 MW at a beam current of 40 A and a beam voltage of 84 kV. Depressed collector operation has been possible up to decelerating voltages of 33 kV without any reduction of the output power. Long pulse operation (10 s at 1 MW) was possible without any signs of a limitation caused by the tube. For this output power the efficiency of the tube could be increased from about 30% without to about 50% with depression voltage. The best performance reached so far has produced an energy per pulse as high as 90 MJ (power 0.64 MW, pulse length 140 s) which is the highest value achieved in gyrotrons operating at this frequency and power level. The pulse-length limitations so far are mainly due to the external system.

Development of a 140-GHz 1-MW continuous wave gyrotron for the W7-X stellarator

The gyrotron TH 1506 B has been developed under a collaboration between TED (Thales Electron Devices formerly Thomson Tubes Electroniques), the association Euratom-CEA and the association Euratom-Confederation Suisse, for application of EC waves on both Tokamaks Tore Supra and TCV. The main features of this tube are: frequency 118 GHz, output power 400 kW, pulse length 210 s (500 kW, 5 s also possible). After acceptance tests in the factory at 500 kW, 5 s, one series tube has been tested in very long pulses at Cadarache. A power of 300 kW for a pulse duration of 111 s has been successfully obtained, validating the design of the main components of the gyrotron. However, a limitation in output power with the nominal working parameters at 300 kW has been observed, and the pulse duration is limited by a strong degassing within the tube. This degassing is due to the excessive heating of the mirror tank of the gyrotron. Investigations are in progress to understand the reasons for the limitation of the output power and some calculations have been made to find how improving the cooling of the mirror tank.

Very long pulse testing of the TH 1506 B 118 GHz gyrotron

The first TH1506B prototype showing problems of overheating and spurious oscillations, a new modified gyrotron was built During the tests, the extwo peaks, which was never predicted by simulations Various low evel tests were performed on the mode converter with different shapes for the launcher but without real improvement Besides measurements, the use of a new software Surf3D[l] showed that the problem mainly comes from the 3rd mirror whose curvature is too high and not well taken nto account by the calculation This analysis software is based on ntegral equations and the complete 3D modelling alowed to determine a new profile for the 3rd mirror An aluminium model of a new mirror was manufactured and thorough low level tests made at FZK showed that there was no double peakThe next step would consist in building a gyrotron based on this new design, to confirm the simulation and to valdate it for long pulses

Upgrade Of The TH1506B 118 GHz Gyrotron Using Modeing Tools

Operation of the 118 GHz very long pulse Gyrotron for the ECRH experiment on Tore Supra

The characterization of the electromagnetic field at the electron cyclotron frequency is one important point for the ECRH (Electron Cyclotron Resonance Heating) installation under development at the CEA Cadarache. This characterization is based on a mathematical decomposition of the electromagnetic field over the various radiating modes of an oversized corrugated waveguide. To perform this determination, which principle is given in the paper, one has to access the amplitude and the phase of the full electric field on a plane transverse to the propagation direction. It is possible to obtain amplitude and phase diagrams of the two crossed polarizations at low level. At high level, in the output of a gyrotron, one uses only thermal measurements and the phase is reconstructed from the amplitude diagrams. The paper exposes a complete validation of this method and gives the results of the high level characterization.

Characterization of the 118 GHz ECRH output beam on tore supra (CEA cadarache)

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

C. Lievin

Author Tools

Chat about Author