Poly(lactic acid) blends in biomedical applications

The development of a thermally conducting composite material that can be rapidly 3D printed into prototype objects is presented. The composite structures containing 10, 20, 25 and 30% (w/v) of 2–4 micron sized synthetic diamond microparticles added to the acrylate polymer were produced using a low cost stereolithographic 3D printer. The prepared materials were characterised according to heat transfer rates, thermal expansion co-efficients and contact angles, and analysed using high resolution electron microscopy, thermogravimetric analysis and thermal imaging. The composites displayed minor enhancements in heat transfer rates with incrementing diamond content upto 25% (w/v), however a significant improvement was observed for the 30% (w/v) polymer–diamond composite, based on an interconnected diamond aggregate network, as confirmed by high resolution scanning electron microscopy. The developed material was used in the fabrication of prototype 3D printed heat sinks and cooling coils for thermal management applications in electronic and fluidic devices. Infrared thermal imaging performed on 3D printed objects verified the superior performance of the composite compared to the inherent polymer.

/pdf/a-3d-printable-diamond-polymer-composite-a-novel-material-4x21fb8iys.pdf

A 3D printable diamond polymer composite: a novel material for fabrication of low cost thermally conducting devices

Investigation of mechanical properties and applications of polylactic acids - A review

Sustainable polymers are important alternatives to plastics and elastomers derived from petroleum resources. Poly(lactide) (PLA), a commercially available sustainable plastic, is a well-known succe...

Crazing mechanism and physical aging of poly(lactide) toughened with poly(ethylene oxide)-block-poly(butylene oxide) diblock copolymers

Modification and extrusion coating of polylactic acid films

Polylactide (PLA), a main biodegradable and biobased candidate for the replacement of petrochemical polymers, is stiff and brittle at room conditions. It is therefore of high interest to formulate new PLA-based materials suitable for applications demanding flexibility and toughness. In this work, novel blends of PLA with polyhedral oligomeric silsesquioxanes (POSS) grafted with longer (P1) and shorter (P2) arms of ethylene glycol derivatives were prepared and studied. It was hypothesized that, owing to their architecture with the central POSS cage grafted with arms, miscibility and stability of the blends could be improved. Indeed, PLA/P1 blends were homogeneous despite P1 relatively high M
 w of 9,500 g mol−1. The blend with 20 wt% of P1, having T
 g at 16 °C, was transparent and flexible, elastomer-like material with excellent drawability. The blend remained homogeneous and retained its good drawability as well as flexibility during 6 months of aging at room temperature: a 2 % secant modulus of elasticity well below 100 MPa, a low yield stress below 2 MPa, and and a large strain at break of 8 (800 %). Contary to that, PLA/P2 blends were only partially miscible. Nevertheless, owing to the liquid state of the dispersed phase, the blend with 15 wt% of P2 was transparent and ductile, with T
 g at 49 °C, a relatively high yield strength of 29 MPa, and a large strain at break of 2.3 (230 %). The toughening mechanism involved the initiation of crazes and facilitation of their propagation by the liquid inclusions via the local plasticization effect.

/pdf/novel-blends-of-polylactide-with-ethylene-glycol-derivatives-3oezb6azuo.pdf

Novel blends of polylactide with ethylene glycol derivatives of POSS

Blending of polylactide (PLA) with low stereoregularity and polyhedral oligomeric silsesquioxane grafted with arms of poly(ethylene glycol) methyl ether, acting as a plasticizer, allowed us previously to obtain a novel stable elastomeric-like material. The present contribution focuses on the properties of semi-crystalline PLA plasticized with this compound. Melt blends of PLA with 5–15 wt% of the plasticizer, were compression molded, quenched and annealed, which enabled cold-crystallization. The glass transition temperature of the blends and their drawability depended on their crystallinity and plasticizer content. The best ductility was reached at the plasticizer content of 15 wt%; the achieved strain at break was 6.5 (650%) and 1.3 (130%), for the quenched and annealed material, respectively. The latter value exceeded 20 times the strain at break of neat crystalline PLA. The tensile toughness of the annealed 15 wt% blend was 12 times larger than that of crystalline PLA. Moreover, annealing of 15 wt% blend improved its yield strength by 40%. Despite the two peaks of the loss modulus, indicating the two glass transitions in this blend, no heterogeneities were found by scanning electron microscopy, indicating that the plasticizer enriched phase formed instead of distinct inclusions of the plasticizer.

Novel Tough Crystalline Blends of Polylactide with Ethylene Glycol Derivative of POSS

The influence of diamond powders on properties of isotactic polypropylene (PP) was investigated. PP composites containing 0.2—5 wt % of the powders with particles of average size between 100 nm and 1 μm were prepared, and their structure and properties were examined. Dispersion of each filler depended on its grain size and content. The presence of fillers raised the crystallization temperature of PP matrix by up to few Celsius degrees. The modulus of elasticity of composites increased with increasing filler content, by up to 40 % in comparison to neat PP. The tensile impact strength of the composites with 1 μm powders and also the other composites at the filler content as low as 0.2 wt % improved by up to 30 %. The composites did not exhibit any decrease in the yield strength and retained good drawability. The elongation at break exceeded 1000 % in most cases. Examination of the uniaxially drawn specimens revealed that the filler grains separated from the PP matrix during drawing.

Structure, thermal and mechanical properties of polypropylene composites with nano- and micro-diamonds

Handle everyday research tasks with reliable, citation-backed results

Your personal Research Agent to handle research tasks with citation-backed results

Popular Tasks used by Researchers

How can I help with your research?

Meet SciSpace

Get more enhanced response by uploading the PDFs you want me to reference.

No relevant PDFs in your library

SciSpace is the AI research assistant for academics. Run systematic literature reviews on 280M+ papers, and write papers with cited sources. Trusted by 1M+ students, PhDs & researchers.

SciSpace | AI for Research

Analyze PDFs

Code & Manuscripts

Funding & Grants

Literature & Patents

Medical & Clinical Data

Systematic Review

Visualize & Present

Web & Data

Build a Google Scholar-like website for your research.

Build a website

Create charts and images for your research

Create a Chart

Write a paper for submission to a journal

Draft a manuscript

Patent Search

Design eye-catching scientific posters in minutes.

Scientific Poster Generation

Systematic Literature Review

One task is running at the moment. Your messages will be shown right after.

Drag and drop or click here to browse

Loved by <highlight>1 million+</highlight> researchers

Extract a list of specific topics and their sources from unstructured text

Topics

Compare and analyze relevant papers that matches with your search

Papers

Get insights from PDFs and bookmarked papers from your library

My library

Recent searches

Try searching for:

Catch AI-generated content in scholarly and non-scholarly content

{ai} Detector

Ai Writer

Get PDF Summaries, highlighted text explanations 

Chat with PDF

Effortlessly create in-text citations and bibliographies in APA and 2,500 other formats

Citation generator

Get explanations, summaries, and answers on academic papers

Ease up your research workflow with {scispace}'s cohort of exciting AI tools

Elevate your academic writing skills and convey your ideas the way you want

Paraphraser

Explore our range of reading and writing tools

Your file is being prepared and should be ready in a few minutes. If it's a large file, it might take a bit longer. You can close this window, and we'll email you the file when it's done.

You have reached a maximum limit of <strong>{limit}</strong> columns in the table. Remove at least <strong>1</strong> column to add or create another one.

Anna Zubrowska

Author Tools

Chat about Author

Papers

Novel blends of polylactide with ethylene glycol derivatives of POSS

Novel Tough Crystalline Blends of Polylactide with Ethylene Glycol Derivative of POSS

Structure, thermal and mechanical properties of polypropylene composites with nano- and micro-diamonds